Contact Us

LTC6820IMS#TRPBF

Brand: Analog Devices
Analog Devices LTC6820IMS#TRPBF is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

LTC6820IMS#TRPBF — Analog & Mixed-Signal ICs | Superb Automation

LTC6820IMS#TRPBF

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The LTC6820IMS#TRPBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

LTC6820IMS#TRPBF: one megabit down a hundred metres of twisted pair, because a bit is a round trip

The LTC6820 converts a standard serial peripheral interface into isoSPI, a two wire differential interface that runs over a single twisted pair through a small pulse transformer and carries the same traffic up to 1 Mbps and up to 100 metres of cable. It is AEC-Q100 qualified, idles at 2 microamps, wakes on activity, works from 2.7 V to 5.5 V, and its logic side accepts any level from 1.7 V to 5.5 V. It appears in battery management systems where a stack of monitors sits at a high potential and the controller sits at ground, and it needs no software change in most existing interface code.

What the vendor page states

ParameterValue
Functionserial peripheral interface to isolated two wire interface
Data rate1 Mbps
Cable lengthup to 100 m of twisted pair
Isolationthrough a standard pulse transformer, one transformer per node
Idle current2 microamps
Wake upautomatic detection on activity
Supply2.7 V to 5.5 V, logic interface 1.7 V to 5.5 V
Noiselow emissions and low susceptibility, configurable for either
QualificationAEC-Q100, minus 40 C to plus 125 C
Packages16 lead QFN and MSOP

The cable delay is the reason the rate stops at one megabit

A twisted pair propagates at roughly 0.66 of the speed of light, which is 198 million metres per second, or 5.05 ns for every metre. A hundred metres is therefore 505 ns one way and 1010 ns for a round trip, which is just over the 1000 ns bit period at 1 Mbps. The interface is bidirectional over one pair and the acknowledgement has to come back inside the bit, so the rate is set by the cable, not by the silicon. At 50 metres the round trip is 505 ns and there is half a bit of margin; at the full 100 metres there is essentially none, which is why a system that needs more speed shortens the cable rather than raising the clock.

Two microamps idle is 10 microwatts

Two microamps at 5 V is 10 microwatts, and left idle for a year that is 0.09 Wh, which is the figure that matters in a battery pack that sits in a warehouse for months before it is installed. The automatic wake on activity is what makes that current possible: the part sleeps until an edge appears on the pair, then answers, then sleeps again. A system that polls the bus continuously defeats the saving, and the polling interval in the controller is therefore part of the power budget rather than a software detail.

One transformer per node, and what that costs

The isolation comes from a pulse transformer rather than from a barrier inside the package, so the isolation voltage is chosen at the transformer, not at the chip. That is what makes the part usable on a battery stack where every node sits at a different potential: each board carries its own small transformer and the pair is daisy chained. The trade is that the transformer's common mode capacitance and its turns ratio are now part of the link, and a transformer chosen for cost rather than for the vendor's recommended part will change the eye at 100 metres. At 1 Mbps and 62.5 thousand 16 bit words per second the traffic is modest, so a buyer should spend the transformer budget on isolation rating rather than on bandwidth.

Before the order goes out

The automotive qualified and industrial versions share the datasheet and differ in grade, so a bill of materials that mixes an I suffix with a higher grade part will pass inspection and fail the qualification audit. The pin to pin cross reference lists the interface devices that share this 16 lead footprint, the BOM shortage recovery page is where to start when the QFN line is short, and the analog and mixed signal category page holds the rest of the interface family.

Request Quote — In Stock, 100% New & Original, Full Warranty