ADA4177-2ARMZ-R7
Product Specifications
ADA4177-2ARMZ-R7
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The ADA4177-2ARMZ-R7 from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
ADA4177-2ARMZ-R7: 32 V of overvoltage protection in front of a 60 microvolt offset
The ADA4177-2ARMZ-R7 is the dual member of the ADA4177 family from Analog Devices, a precision amplifier with two features that rarely appear together with dc accuracy: input protection against signal excursions 32 V beyond either supply, and an integrated EMI filter that rejects 70 dB at 1000 MHz. It keeps a 60 microvolt maximum offset, 1 nA of bias current and 8 nanovolts per root hertz of noise while doing it.
What the vendor publishes
| Parameter | Value |
|---|---|
| Channels | two, single and quad versions in the same family |
| Offset | 60 microvolts maximum at 25 C, 2 microvolts typical |
| Drift | 1 microvolt per degree C maximum |
| Bias current | 1 nA maximum at 25 C |
| Noise | 8 nV per root hertz typical at 1 kHz |
| Open loop gain | 100 dB minimum over the full supply and temperature range |
| Overvoltage | 32 V above and below either supply rail |
| EMI rejection | 70 dB typical at 1000 MHz, 90 dB typical at 2400 MHz |
| Supply current | 500 microamps typical per amplifier |
| Bandwidth | 3.5 MHz gain bandwidth, 6 MHz at unity gain minus 3 dB |
| Supply | specified at plus or minus 5 V to 15 V, operates 2.5 V to 18 V |
| Stability | stable into more than 1000 pF, no phase reversal |
| Long term | 2 microvolts typical drift over 10,000 hours |
| Temperature | -40 to +125 C |
47 V at the input with no clamp diode
On plus or minus 15 V rails, 32 V beyond either supply means the input can be taken to plus or minus 47 V and the amplifier survives. The usual alternative is a series resistor and a Schottky pair to the rails, and both of those cost something: the resistor adds Johnson noise and an IR drop that grows with the source impedance, and the diodes add leakage current and capacitance that move with temperature. For a 4 to 20 mA loop receiver or an industrial front end that sees a miswired connector, keeping the protection inside the amplifier keeps the error budget intact.
EMI rejection read in microvolts
Seventy decibels at 1000 MHz turns 100 mV of pickup at the input pins into 31.6 microvolts referred to the input. At 2400 MHz the 90 dB figure turns the same 100 mV into 3.16 microvolts. Against a 60 microvolt offset budget the 1 GHz number is the same order as the dc error, which is the reason the vendor publishes both frequencies rather than a single typical figure.
Noise over the bandwidth the part actually has
Eight nanovolts per root hertz integrates to 800 nV over 10 kHz and 15 microvolts over the full 3.5 MHz. Two amplifiers at 500 microamps each is 15 mW from plus or minus 15 V, low enough that a four channel front end does not become a thermal problem. The term to watch is bias current against source impedance: 1 nA into 1 Mohm is 1 mV, which is seventeen times the offset, so the protection and the precision only pay off when the source impedance is moderate.
Two questions buyers ask
Does the overvoltage protection remove the need for external clamps? For signal excursions yes, up to the 32 V figure beyond the rails. It does not replace a transient suppressor for a lightning or surge specification, which is a different class of event and a different standard.
Single, dual or quad? The ADA4177-1 and ADA4177-4 are the single and quad members. The dual is the usual choice for a two channel loop receiver, and the quad goes into a four channel module where the board area matters more than the channel isolation.
SUPERB quotes the ADA4177-2ARMZ-R7 against this row and confirms the grade and package before shipment. Amplifier alternatives are compared under amplifier cross reference, a same footprint check starts at pin to pin cross reference, and the category index is analog and mixed signal ICs.
Request Quote — In Stock, 100% New & Original, Full Warranty