Contact Us

LT8608IMSE#TRPBF

Brand: Analog Devices
Analog Devices LT8608IMSE#TRPBF is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

LT8608IMSE#TRPBF — Analog & Mixed-Signal ICs | Superb Automation

LT8608IMSE#TRPBF

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The LT8608IMSE#TRPBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

LT8608IMSE: The MSOP Pin That the DFN Does Not Have

Two versions of the same 42 V, 1.5 A buck regulator reach the market in this family: a 10-lead MSOP with an exposed pad and an 8-lead 2 by 2 mm DFN. The silicon is the same, the 35 ns minimum on time is the same and the 1.5 A rating is the same, but the MSOP bonds out SYNC and TR/SS while the DFN does not. That single difference decides whether a board can be synchronised to a system clock, whether spread spectrum is available, and whether the soft-start ramp can be set. The I grade here is the 125 C junction code.

Published values

ParameterValue
Part numberLT8608IMSE, industrial grade, 10-lead MSOP with exposed pad
Junction rangeMinus 40 C to 125 C, H grade reaches 150 C
Input voltage range3.0 V to 42 V
Output current1.5 A continuous
Minimum switch on time35 ns
Frequency range200 kHz to 2.2 MHz
Quiescent current1.7 uA typical
Power good windowPlus or minus 8.5 percent
Mode controlSYNC pin selects burst, pulse-skipping or spread spectrum
Soft startTR/SS pin sets the ramp or tracks an external rail
Thermal resistance40 C/W junction to ambient, 10 C/W junction to case
Package10-lead MSOP with exposed pad, 11 pins including the pad

What the SYNC pin actually selects

The pin is not only a clock input. Depending on how it is driven the part runs in Burst mode, in pulse-skipping mode, in forced continuous mode or with spread spectrum modulation, and the datasheet offers the mode as part of the ordering information for the DFN parts because those pins are not available there. On the MSOP a single resistor or a logic level sets the behaviour at the time the board is built, which is a configuration freedom the smaller package gives up.

For a product that has to pass an EMC limit, spread spectrum is the reason to choose the MSOP. The modulation dithers the switching frequency by a few percent, which spreads the emission peak, and it costs nothing in efficiency. For a product that has to be synchronised to a system clock to avoid beating with another converter, the SYNC input is the reason, and the DFN cannot do it at all.

Soft start and tracking on TR/SS

The TR/SS pin sets the output ramp with a capacitor, and it can also be driven by another rail so the two rise together. In a system with several rails and a defined power-up order, that is the difference between a controlled sequence and a race. A DFN part with the pin absent has a fixed internal ramp, which is adequate for a single rail and awkward in a multi-rail system.

The 8.5 percent power good window is 280 mV on a 3.3 V rail, and the flag can be used either as a reset to downstream logic or as a fault output. The same window on a 5 V rail is 425 mV, so the timing of the flag depends on the rail it watches.

The thermal question at 1.5 A

At 40 C/W the MSOP passes 0.5 W with a 20 C rise and 0.7 W with 28 C. The conduction loss of the internal switch at 1.5 A is what fills that budget, and the same 200 milliohm figure that gives a 300 mV drop at 1.5 A gives 0.45 W. Efficiency at 0.5 A and 5 V out from 12 V in is quoted above 92 percent, which is the operating point where the part is comfortable; the corner is 1.5 A at 42 V in, where the switch loss and the gate charge together are the limit.

A 125 C junction in an 85 C enclosure allows 40 C of rise, which is 1 W through the 40 C/W path. A 150 C H grade allows 65 C of rise, 1.6 W, which is why the H exists for automotive and industrial boxes that run hot.

For a board that has to keep running while a reel runs out, the power management cross reference is where the family alternatives sit, the pin to pin cross reference is the check list before a substitute goes in, and how to verify a drop in replacement is how a gap is covered without a new line item.

Two questions buyers ask

Can the DFN version be used where the MSOP is specified? Only if SYNC and TR/SS are unused. The DFN does not bond those pins, so a board that drives them loses its mode control and its soft-start setting.

Does the I grade cover 150 C? No, the I grade is specified to 125 C junction. The H code is the 150 C part in the same package.