Contact Us

AD8065ARZ-REEL7

Brand: Analog Devices
Analog Devices AD8065ARZ-REEL7 is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

AD8065ARZ-REEL7 — Analog & Mixed-Signal ICs | Superb Automation

AD8065ARZ-REEL7

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The AD8065ARZ-REEL7 from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

AD8065ARZ-REEL7: 145 MHz small signal, 28 MHz at two volts peak to peak

The AD8065 is a single FastFET amplifier: a FET input stage with 1 pA of bias current and 7 nV per root hertz of voltage noise, on a process that also gives it 145 MHz of bandwidth at a gain of 1 and 180 V per microsecond of slew rate, for 6.4 mA of supply current. It runs from 5 V to 24 V on a single supply, swings to the rails, and delivers up to 30 mA of output current. The combination of a picoamp input and a 145 MHz bandwidth is the reason it appears in front of photodiodes and in the first stage of instruments where the source impedance is high and the signal is fast.

What the vendor page states

ParameterValue
Bandwidth145 MHz at minus 3 dB, gain of 1
Slew rate180 V per microsecond at a gain of 2
Input bias current1 pA
Voltage noise7 nV per root hertz at 10 kHz
Current noise0.6 fA per root hertz at 10 kHz
Offset voltage1.5 mV maximum
Common mode rejection100 dB
Distortionminus 88 dBc spurious free dynamic range at 1 MHz
Supply range5 V to 24 V, single supply, rail to rail output
Supply current and drive6.4 mA typical, 30 mA of load current
Package and gradeSOIC, MSOP and SOT-23, minus 40 to plus 85 C

Bandwidth against amplitude

The 145 MHz figure is a small signal number. Slew rate sets the largest frequency a full amplitude sine can reach, and 180 V per microsecond gives 57.3 MHz at 1 V peak to peak, 28.6 MHz at 2 V peak to peak and 11.5 MHz at 5 V peak to peak. An application that needs a 2 V peak to peak signal into a converter is therefore buying a 29 MHz amplifier, not a 145 MHz one, and the difference is the first thing that shows up when a first article is measured at full scale instead of at minus 30 dBm.

Where the FET input earns its place

One picoamp into 1 Mohm is 1 microvolt, and the current noise of 0.6 fA per root hertz over a 1 MHz bandwidth through 10 Mohm is 6 microvolts, still below the 7 microvolts of voltage noise over the same bandwidth. That balance is what makes the part usable with a high impedance source: with a bipolar input, 1 microamp of bias current would produce a volt of offset across the same resistor. Above about 10 Mohm the current noise term starts to dominate and a different device is called for.

Thirty milliamps of drive against six of quiescent

The output can source 30 mA while the part draws 6.4 mA, which is 4.7 times its own supply current. Driving 100 ohm at 5 V dissipates 250 mW in the output stage, 7.8 times the 32 mW quiescent figure, so the thermal calculation for a cable driver is about the load and not about the quiescent current. At 24 V supply the quiescent alone is 154 mW, which is the case where the package and the copper under it decide the junction temperature.

Before the order goes out

The automotive version carries a W in the part number and is specified to plus 105 C, but only up to plus and minus 5 V of supply, so it is not a drop in replacement for a 24 V position. The amplifier cross reference lists the FastFET alternatives by bandwidth and noise, the obsolete part hub tracks the older high speed FET input parts that this generation replaces, and the analog and mixed signal category page holds the rest of the amplifier family.

AD8065ARZ-REEL7: the ARZ body is the industrial grade, and 24 V costs 154 mW

The vendor lists the family over -40 C to +85 C for the industrial bodies and states separately that AD8065WARTZ-R7 is the part fully qualified for automotive use. This order code is not that one, so a specification that asks for -40 C to +85 C is asking for this code, while an AEC-Q100 requirement has to move to the W code rather than be inferred from the family heading. The supply range of 5 V to 24 V is the second thing the code decides in practice: at the top of that range and 6.4 mA per amplifier typical, the part dissipates 154 mW before any load current, and that heat leaves through an 8-lead SOIC body whose pads are the only path.

ItemPublished valueWhat it means for this code
Grade-40 C to +85 C, W code for automotiveARZ is the industrial body, not the qualified one
Supply5 V to 24 V, single or dual154 mW at 24 V and 6.4 mA before load
Bandwidth145 MHz at a gain of +114.5 MHz closed loop at a gain of 10
Slew rate180 V/us at a gain of +2A 20 V peak to peak swing tops out near 1.43 MHz
Input bias1 pA, 0.6 fA per root hertz1 mV only at 1 Gohm of source impedance
Load drive30 mA, 6.4 mA quiescentThe load current is five times the part current
BodiesSOIC-8, MSOP-8, SOT-23-5The reel suffix follows the body, so both fields belong on the order

One picoamp is a claim about the source, not about the part

A bias current of 1 pA becomes 1 mV only when the source impedance is 1 Gohm, and at 10 Mohm it is 10 uV, which is below the 1.5 mV maximum offset and therefore invisible. That is the useful way to read the number: the FET input buys nothing on a 10 kohm network and everything on a photodiode or a high value feedback resistor. The currency noise of 0.6 fA per root hertz only becomes visible on the same high impedance nodes, where it is compared against the thermal noise of the resistor rather than against the amplifier.

Two headroom questions that the 24 V range creates

The output is rail to rail, but the input common mode range is not the whole rail, and the vendor notes no phase reversal rather than a rail to rail input, so a follower that sits at the positive rail is the case to check on a circuit review. On a 24 V single supply the quiescent dissipation of 154 mW in a small body sets a practical ceiling on how many channels can sit in one package area. At plus or minus 12 V the same part runs a 20 V peak to peak signal at 1.43 MHz before the slew rate, not the bandwidth, becomes the limit.

Buying this order code

The W grade is a separate order code, so a BOM line that says AD8065 without the suffix does not decide the temperature grade. Our analog and mixed signal line card carries the family, and when the W code is missing from a distributor shelf the route is a documented alternate through the pin to pin cross reference rather than a substitution by name. Reel quantities and date codes are confirmed per order on the lead time page.

Request Quote — In Stock, 100% New & Original, Full Warranty