LT8390EUFD#TRPBF
Product Specifications
LT8390EUFD#TRPBF
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The LT8390EUFD#TRPBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
LT8390EUFD: A Four-Switch Buck-Boost That Holds 12 V From 4 V to 60 V
The LT8390 is a synchronous four-switch buck-boost controller with one inductor, which means it can hold its output above, below or equal to the input without a mode change that shows up on the output. The feedback reference is 1 V, the output accuracy is 1.5 percent from 1 V to 60 V, the input range is 4 V to 60 V, and the switching frequency is adjustable from 150 kHz to 650 kHz. This order code is the E grade in the 28-lead 4 by 5 mm QFN, and the numbers that decide the inductor and the FETs are the duty cycle in each region and the 1.5 percent output window.
Published values
| Parameter | Value |
|---|---|
| Input voltage range | 4 V to 60 V |
| Output voltage range | 0 V to 60 V |
| Feedback reference | 0.985 to 1.015 V, 1.00 V typical |
| Output accuracy | 1.5 percent |
| Current accuracy | 3 percent with the monitor output |
| Switching frequency | 150 kHz to 650 kHz, adjustable and synchronisable |
| Spread spectrum | Plus or minus 15 percent triangle modulation |
| Quiescent current | 270 uA not switching, 2.8 mA maximum |
| Shutdown current | 1 uA typical |
| Internal rail | 5 V, 110 mA current limit |
| Thermal package | 28-lead 4 by 5 mm QFN, 28-lead TSSOP alternative |
| Grade | E, minus 40 C to 125 C junction |
Duty cycle in three regions
A 48 V input to a 12 V output is a 25 percent duty in the buck region, so at 650 kHz the top switches are on for 385 ns of a 1.54 us period. At 4 V input to a 12 V output the converter is in the boost region and the duty is 66.7 percent, which is 1.03 us of the same period. Near unity, where the input and the output are both 12 V, the part runs at the boundary between the two regions and the transition is the interesting case, because that is where a controller without a proper handover produces a notch on the output.
The 150 kHz to 650 kHz range is narrow on purpose. A four-switch buck-boost has four gate drives and one inductor, and the losses in the two extra switches are only tolerable if the frequency stays in this band. A product that wants 2 MHz for a small inductor cannot use this part, and one that wants 50 kHz for efficiency cannot either.
What 1.5 percent means at 12 V and at 48 V
The output accuracy is quoted as a percentage of the setpoint, so 1.5 percent at 12 V is 180 mV and at 48 V it is 720 mV. The 1 V reference with its 1.015 V upper limit is 1.5 percent on its own, which leaves nothing for the divider. Two 0.1 percent resistors add about 0.14 percent and keep the total near 1.7 percent, and two 1 percent resistors push it to 3.5 percent, which is more than the specification.
The current monitor is quoted at 3 percent, so a 4 A limit is plus or minus 120 mA. That is a limit for protection and reporting, not a precision measurement, and a battery charger that needs an accurate current should use the monitor as an indication and calibrate in production.
Quiescent current and the shutdown path
The part draws 270 uA when it is not switching and 2.8 mA at worst, which at 60 V is 168 mW and a reminder that a wide input controller is not a micropower part. The 1 uA shutdown is what allows a battery system to leave the rail off, and the load switch driver on the part is what disconnects the output from the input during shutdown rather than leaving the body diodes to conduct.
The four-switch arrangement means four gates to drive and one inductor, and the inductor carries the full current in every region. That is the trade against a transformer based converter: fewer magnetic parts and a single winding, at the cost of more switches and a control loop that has to hand over between regions without a disturbance.
Buyers usually arrive at the power management cross reference to find the family alternatives, then use the ADI second source page to confirm a substitute before it is fitted; BOM shortage recovery is the routine for a part that has already stopped shipping.
Two questions buyers ask
Does the output stay regulated when the input crosses the output voltage? Yes, that is the point of the four-switch arrangement, and the part is specified to hold the output through the region where the input and output are equal. The transition is a control loop behaviour rather than a mode switch the user has to manage.
Can it work as a current source? Yes, it regulates output voltage, input current or output current, and the monitor output reports the current at 3 percent accuracy. The current loop is the reason it appears in battery and supercapacitor chargers.