Contact Us

LT3757AHMSE#TRPBF

Brand: Analog Devices
Analog Devices LT3757AHMSE#TRPBF is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

LT3757AHMSE#TRPBF — Analog & Mixed-Signal ICs | Superb Automation

LT3757AHMSE#TRPBF

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The LT3757AHMSE#TRPBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

LT3757AHMSE: Improved Transient Response at a 150 C Junction

Two independent changes land in this order code: the A suffix, which is the improved load transient version of the controller, and the H grade, which raises the guaranteed junction range to minus 40 C to 150 C. The combination is what a converter inside a sealed enclosure with a pulsed load needs, because the enclosure sets the ambient and the load sets the loop requirement. Everything else is the 2.9 V to 40 V current mode controller that runs boost, SEPIC, inverting and flyback stages from a 7.2 V gate supply in a 10 lead MSOP.

Published values

ParameterValue
Input range2.9 V to 40 V
Guaranteeminus 40 C to 150 C junction, tested
Thermal resistance40 C/W junction to ambient in the MSOP
Transient behaviourimproved relative to the non A part
Feedback point1.6 V positive, minus 0.800 V negative
SENSE current limit110 mV typical
Minimum on and off time220 ns
Switching frequency50 kHz to 1 MHz
Gate drive supply7.2 V regulator, 17.5 V overvoltage lockout
Quiescent current2.2 mA maximum, 1 uA shutdown
Package restrictionH grade is MSOP only, the DFN stops at 125 C
Life dataderated above a 125 C junction

The ambient sets the power budget, the loop sets the capacitor

At 105 C ambient inside the enclosure, a 150 C junction allows 45 C of rise, which at 40 C/W is 1.1 W for the controller. That number has to cover the 88 mW of quiescent current at 40 V, the gate drive, and the regulator losses, and it leaves about 0.8 W for gate charge, which is a 60 nC FET at 400 kHz with room to spare. A larger FET with 150 nC of gate charge would double that term and put the package at its limit, so the thermal answer and the FET choice are the same decision.

The loop answer is separate. A pulsed load produces a dip that the output capacitor supplies until the loop responds, and the improved transient of the A version reduces the time the loop takes. On a 24 V output feeding a 1 A pulse, the dip is set by the capacitor's ESR and capacitance for the first few microseconds and by the loop after that, so a part with better transient response lets a smaller capacitor meet the same dip specification. The saving is often larger than the price difference between the A and non A parts.

Why the A and H combination is not redundant

The H grade alone gives the temperature range with the older transient behaviour, and the A grade alone gives the transient behaviour up to a 125 C junction. A board that needs both does not get there by combining two part numbers: the A H order code is the only listing with both, and it is the one to quote when a customer's specification asks for a 105 C ambient and a load step requirement in the same document.

The H grade also restricts the package to the MSOP. The DFN listing in this family stops at a 125 C junction, so a 3 by 3 DFN footprint cannot carry an H grade part even though the thermal resistance of the two packages is within 3 C/W of each other.

Fault behaviour in a hot box

The on chip overtemperature protection is intended for momentary overload, and the datasheet is explicit that continuous operation above the maximum junction impairs reliability. In a sealed enclosure the failure mode is not a dramatic shutdown: it is a converter that runs at 140 C junction for years and drifts out of specification first on the oscillator and then on the feedback point. Setting the target near 125 C junction with the 150 C rating as margin is what the life data supports.

The FBX overvoltage lockout is the other protection worth knowing. It is measured relative to the regulated feedback value and it is what stops the output running away when the feedback divider opens, which in a hot enclosure is a real failure mode for a resistor that is dissipating more than it should.

For a board that has to keep running while a reel runs out, the power management cross reference is where the family alternatives sit, defense grade components is the check list before a substitute goes in, and vendor consolidation is how a gap is covered without a new line item.

Two questions buyers ask

Does the A H part cost more than an A I part? Yes, the wide temperature test is the premium, and it is only worth paying where the ambient demands it. A board that sits at 70 C ambient with a 0.3 W controller is at 82 C junction on the I grade and has no reason to buy the H.

Can the H grade be used with the DFN footprint? No. Only the MSOP listing carries the 150 C junction and the wider storage range, so a DFN footprint has to be changed before an H grade part can be fitted.