AD8137YRZ-REEL7
Product Specifications
AD8137YRZ-REEL7
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The AD8137YRZ-REEL7 from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
AD8137YRZ-REEL7: thirteen milliwatts of differential driver and a hundred nanoseconds to settle
The AD8137 is a fully differential amplifier built to drive the input of a differential analog to digital converter, with a rail to rail output, an output common mode voltage set by a single pin, and a quiescent current of 2.6 mA from a 5 V supply. The order code reads Y for the extended industrial temperature range of minus 40 to plus 125 C, R for the 8-lead small outline body, Z for RoHS and REEL7 for the 7 inch reel. The internal common mode feedback loop does two things at once: it holds the two outputs balanced, which suppresses even order distortion, and it lets the common mode be set independently of the differential signal, which is what a converter's input common mode pin needs.
What the vendor page states
| Parameter | Value |
|---|---|
| Topology | fully differential, differential or single ended to differential |
| Quiescent current | 2.6 mA at 5 V, 450 microamps in power down |
| Output | rail to rail, common mode set by a dedicated pin |
| Distortion | 12-bit SFDR performance at 500 kHz |
| Settling | 100 ns to 0.02 percent |
| Input offset | plus or minus 2.6 mV maximum, offset current 0.45 microamps maximum |
| Gain setting | external four resistor network, differential and common mode feedback internal |
| Package and range | 8-lead SOIC or 3 by 3 mm LFCSP, minus 40 to plus 125 C |
Thirteen milliwatts running, 2.25 milliwatts asleep
2.6 mA at 5 V is 13 mW for the whole driver, and the power down pin drops it to 450 microamps, 2.25 mW, a ratio of 5.8 to 1. In a battery instrument that samples in bursts, that ratio is the reason to use the pin rather than to switch the supply: the wake up time from power down is short enough to be inside the acquisition window of the next conversion, while a regulator's start up is not. Across a four channel analog front end the same arithmetic gives 52 mW running and 9 mW asleep, which is the number to put against a converter's own 90 mW per channel before deciding that the amplifier is the small term.
Two point six millivolts of offset is five LSB of a twelve bit converter
On a 2 V peak to peak input range, one LSB of a 12-bit converter is 488 microvolts, so the 2.6 mV maximum input offset of this amplifier is 5.3 LSB before any converter error is counted. That is a large term for a part chosen to protect a 12-bit measurement, and it is why the offset specification has to be read as a system specification: the same 2.6 mV referred to a 16-bit converter at 4 V p-p would be 42 LSB. The 0.45 microamps of input offset current matters when the feedback network is high impedance, because 0.45 microamps through a 1 kohm resistor is another 0.45 mV, and the two errors do not cancel.
A hundred nanoseconds of settling caps the drive rate at ten megasamples
Settling to 0.02 percent in 100 ns means the amplifier can present a settled value to a converter about every 100 ns, which is 10 MSPS, whatever the small signal bandwidth says. For a converter running at 1 MSPS the margin is ten to one and the driver is not the limit; for a multiplexed front end switching between eight channels, the acquisition window is what the settling time has to fit inside, and at 1 MSPS with a 50 percent duty cycle the window is 500 ns. The rail to rail output is the other half of the interface: the converter's input range is usually a volt or two peak to peak centred on a common mode of about half the supply, and the dedicated common mode pin is what lets the driver follow that reference without a second amplifier.
Before the order goes out
The AD8137 is the low power member of a family that includes faster differential drivers with more output current, so the choice is made on settling time and drive capability, not on pin count. The amplifier cross reference lists the differential drivers by settling time and output swing, the BOM shortage recovery page is where to start when this package is on allocation, and the analog and mixed signal category page holds the rest of the amplifier family.
Request Quote — In Stock, 100% New & Original, Full Warranty