LT1962EMS8-1.8#PBF
Product Specifications
LT1962EMS8-1.8#PBF
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The LT1962EMS8-1.8#PBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
LT1962EMS8-1.8#PBF: 300 mA at 1.8 V, and the 270 mV that sets the input floor
The LT1962EMS8-1.8#PBF is the fixed 1.8 V member of the LT1962 micropower low noise regulator family from Analog Devices. It supplies 300 mA with a 270 mV dropout, runs from 30 microamps of quiescent current, and reaches 20 microvolts rms of output noise once a 0.01 microfarad bypass capacitor is fitted on the reference pin. The part is an eight lead MSOP, and the fixed version removes the feedback divider and its error term.
What the vendor publishes
| Parameter | Value |
|---|---|
| Output | 1.8 V fixed, also 1.5, 2.5, 3, 3.3 and 5 V, adjustable 1.22 V to 20 V |
| Current | 300 mA |
| Dropout | 270 mV |
| Noise | 20 microvolts rms, 10 Hz to 100 kHz, with a 0.01 microfarad bypass |
| Quiescent current | 30 microamps |
| Input range | 1.8 V to 20 V |
| Shutdown current | under 1 microamp |
| Output capacitor | stable from 3.3 microfarad, ceramic, aluminium or tantalum |
| Protection | reverse battery, reverse current, current limit, thermal limit |
| Package | 8 lead MSOP |
The input floor is 2.07 V, not 1.8 V
An output of 1.8 V plus a 270 mV dropout at 300 mA means the input has to stay above 2.07 V for the regulator to stay in regulation at full load. A rail that sags to 2.0 V under a transmit burst will not hold 1.8 V out of this part, it will follow the input down by the dropout. The published dropout falls as the load current falls, so a 30 mA load has far more headroom, but the number on the front of the sheet is the one that has to be met at the worst case load.
Twenty microvolts read as bits
Twenty microvolts rms against a 1.8 V rail is 11.1 parts per million, or 99.1 dB, which is 16.5 bits of dynamic range. Read the other way round: this regulator is not what limits a 12 bit or 16 bit converter on its rail, and it is very close to the limit of an 18 bit one. The bypass capacitor is not optional for that number; without it the noise is higher, so a build that leaves the pin open and quotes 20 microvolts is quoting a different circuit.
Where the 450 mW goes
Dropping 3.3 V to 1.8 V at 300 mA puts 450 mW into the package, which is 54.5 percent efficiency and a 58 to 85 C rise depending on the copper around an eight lead MSOP. Two things follow. At full current the part is a heater, so the thermal path is part of the electrical budget. At light current the 30 microamp quiescent current is the whole story: it is 3 percent of a 1 mA load, 30 percent of a 100 microamp load, and three times a 10 microamp load, which is why the part is aimed at battery instruments that sleep between readings rather than at always-on loads.
Two questions buyers ask
Fixed 1.8 V or the adjustable version? Take the fixed part when 1.8 V is the rail, because the divider and its tolerance disappear and the board loses two resistors. Take the adjustable part when the rail has to be trimmed in production, which is a different requirement from a fixed logic rail.
Does the 0.01 microfarad capacitor have to be there? If the 20 microvolt noise figure is part of the specification, yes. It is a bypass on the internal reference, and it is the difference between the headline number and a higher one.
SUPERB quotes the LT1962EMS8-1.8#PBF against this row and confirms the fixed voltage and the package before shipment. Rail alternatives are compared under power management cross reference, a same footprint check starts at pin to pin cross reference, and the category index is analog and mixed signal ICs.
Request Quote — In Stock, 100% New & Original, Full Warranty