LT3690HUFE#TRPBF
Product Specifications
LT3690HUFE#TRPBF
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The LT3690HUFE#TRPBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
LT3690HUFE: 150 degree junction in a 4 mm by 6 mm package
The LT3690HUFE is the H grade of the 36 V, 4 A synchronous step-down regulator, specified from minus 40 to 150 degrees junction. The electrical core is the same as the rest of the family: 3.9 V to 36 V input with overvoltage lockout through 60 V transients, 4 A maximum output, a 30 milliohm synchronous switch, a 0.8 V reference, a 170 kHz to 1.5 MHz oscillator and 70 microamps of quiescent current in Burst Mode. What the H grade buys is 25 degrees of junction headroom, and what that headroom is worth depends entirely on the thermal resistance of the board under the package.
Published values
| Parameter | Value |
|---|---|
| Input voltage | 3.9 V to 36 V, overvoltage lockout through 60 V transients |
| Output current | 4 A maximum |
| Output voltage | 0.8 V to 20 V |
| High side switch drop | 370 millivolts typical, 600 millivolts maximum at 4 A |
| Low side on resistance | 30 milliohms typical, 60 milliohms maximum |
| Quiescent current | 70 microamps at 12 V in, 3.3 V out, Burst Mode |
| Switching frequency | 170 kHz to 1.5 MHz |
| Package | 26-lead, 4 mm by 6 mm QFN with exposed pads |
| Temperature grade | H, junction from minus 40 to 150 degrees |
| Order code | LT3690HUFE#TRPBF, tape and reel |
What 25 degrees of extra junction rating does and does not buy
A higher junction rating does not make the part run cooler. It moves the point at which the thermal shutdown acts and the point at which the guaranteed limits still hold. A board whose thermal resistance puts the junction at 140 degrees at full load will run at 140 degrees on both the I and the H grade; on the I grade that is outside the specified range and the part is being asked for behaviour nobody has promised.
So the H grade is bought when the calculation says the junction lands between 125 and 150 degrees, not when the ambient is high. That calculation starts from the dissipation: 4 A at 3.3 V out from 12 V in is 13.2 W of output, and at about 90 percent efficiency the loss is 1.5 W. Through a thermal resistance of 40 degrees per watt that is a 60 degree rise over the board temperature, which sits inside the I grade on a 60 degree board and outside it on an 80 degree board.
The conduction loss is in the switch, and the switch is in the package
The high side switch drops 370 millivolts typical at 4 A, which is about 1.5 W while it is on, and its duty cycle at 12 V in and 3.3 V out is a little under 30 percent, so the average is about 0.44 W. The low side switch at 30 milliohms carries the ripple current for the rest of the period. Both are inside the package, and both have to cross the exposed pad.
That is why the via field under the pad is not a cosmetic detail. The pad is the only path, and the copper on the far side of the board is the spreader. At 1.5 W a difference between a good via field and a token one is tens of degrees, which is exactly the margin the H grade was bought to provide.
Overvoltage lockout through 60 volt transients
The input is specified to 36 V with an overvoltage lockout that protects the circuit through 60 V transients, which is what makes the part usable on an automotive or industrial rail where a load dump or an inductive kick arrives through a connector. The lockout acts before the switch, so the output stops regulating rather than the part failing, and the recovery is automatic once the input returns.
What the lockout does not protect is the rest of the board. A downstream converter that keeps running from its own output capacitor will hold its rail for as long as the capacitance allows, and then drop. A system that needs a controlled behaviour through the transient has to decide what happens in that window, and the part's power good flag is the signal that tells it the window has opened.
The pages that answer this most often are the power management cross reference for the family alternatives, BOM shortage recovery for the acceptance test, and vendor consolidation for the case where a replacement has to be fitted before the next build.
Two questions buyers ask
Is the H grade needed for a 105 degree ambient? It depends on the dissipation and the board. A 105 degree ambient with a 60 degree rise puts the junction at 165 degrees, which no grade covers. The decision comes from the loss, the thermal resistance and the board temperature, not from the ambient alone.
Does the 60 V transient rating mean the input can sit at 60 V? No. The operating range is 3.9 V to 36 V. The overvoltage lockout stops switching and protects the circuit through 60 V transients, which is a transient capability rather than a continuous rating.