Contact Us

LT3083EQ#PBF

Brand: Analog Devices
Analog Devices LT3083EQ#PBF is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

LT3083EQ#PBF — Analog & Mixed-Signal ICs | Superb Automation

LT3083EQ#PBF

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The LT3083EQ#PBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

LT3083EQ#PBF: extended grade 3 A regulator, DD-Pak, for parallel rails

The LT3083EQ#PBF is the extended grade of the 3 A single resistor regulator in the 5-lead DD-Pak, lead free finish, rated -40 C to 125 C. It takes 1.2 V to 23 V in and delivers 0 V to 23 V out at 3 A with a 310 mV dropout, a 50 uA SET reference at 1 percent, 40 uV RMS noise over 10 Hz to 100 kHz, under 1 mV of load regulation and a 1 mA minimum load. Stability needs only 10 uF of ceramic on the output, and the pass transistor collector is brought out so the device can run from a separate control supply.

Published values

ParameterValue
Input voltage1.2 V to 23 V
Output voltage0 V to 23 V, one resistor
Output current3 A
Dropout voltage310 mV
Output noise40 uV RMS, 10 Hz to 100 kHz
SET pin current50 uA, 1 percent
Load regulationunder 1 mV
Minimum load current1 mA
Protectioncurrent limit with foldback, thermal limit
Package5-lead DD-Pak, lead free
Temperature range-40 C to 125 C

Two devices, 6 A, one SET resistor

Paralleling is the documented way to go beyond 3 A without moving to a switching stage. Because each device regulates the voltage across its own output, two devices with a common SET node share the current in proportion to their offsets, and the resulting sharing is good enough for most loads. The thermal benefit is the larger one: two devices at 1.5 A each run cooler than one at 3 A, and the heat is spread over two areas of copper. The data sheet also notes that the same arrangement lowers noise, since uncorrelated noise from two regulators adds in root sum square rather than linearly.

Foldback current limit in a hot swap event

The current limit folds back as the output voltage falls, so a short circuit draws less current than a load at the edge of the limit. That behaviour protects the pass transistor and the upstream supply during a hot swap or a card insertion, where the output capacitor looks like a short for the first few hundred microseconds. The trade is start up into a large capacitive load: a foldback limit can hold the rail down if the load capacitor is very large, and the data sheet's start up discussion is worth reading before a 1000 uF bank is placed on the output.

Board copper and the tab

The DD-Pak tab is the output, so the copper underneath is a live rail. For a 2 W dissipation the tab needs a real copper area and vias to the opposite layer; the tab is also the electrical connection to the output plane, which is convenient in a supply section where the output plane is already large. In an enclosure with no airflow, the junction rise over ambient can approach 50 C at 2 W, which leaves margin at 125 C but not much. The TSSOP and DFN bodies of the same device are the alternatives when the board cannot give the DD-Pak tab enough copper.

Ordering notes

EQ is the extended grade DD-Pak with lead free finish, supplied in tubes. I and MP versions of the same body cover the industrial and cold start windows, and moving between grades keeps the electrical table but changes the screening. Our power management cross reference lists the codes against the bodies, the BOM shortage page covers substitution when the extended grade is short, and the vendor consolidation page explains grouping the order.