Contact Us

ADF4350BCPZ-RL7

Brand: Analog Devices
Analog Devices ADF4350BCPZ-RL7 is a analog & mixed-signal component designed for Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

ADF4350BCPZ-RL7 — Analog & Mixed-Signal ICs | Superb Automation

ADF4350BCPZ-RL7

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The ADF4350BCPZ-RL7 from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

ADF4350BCPZ-RL7: 137.5 MHz Comes From Dividing a 2.2 GHz VCO, and Every Division Costs Level

The ADF4350 is a fractional N or integer N synthesizer with an integrated VCO that tunes from 2200 MHz to 4400 MHz, followed by programmable dividers of 1, 2, 4, 8 or 16 to reach outputs as low as 137.5 MHz, with typical rms jitter below 0.4 ps and a 3.0 V to 3.6 V supply. The output range on the front page looks like a tuneable oscillator from 137.5 MHz to 4.4 GHz. It is not: the oscillator always runs in its own band and the low frequencies are divisions of it, which is why a 137.5 MHz output is 24 dB lower in level than the same signal at 2.2 GHz and why the phase noise at low frequency is better than the VCO figure, not worse.

Dividers change both level and noise

Each division by two lowers the output by 6 dB and lowers the phase noise by 6 dB, so the path from the VCO through all four dividers gives 24 dB less level and 24 dB less phase noise at 137.5 MHz. The VCO figure published for the part is minus 114 dBc per hertz at 10 kHz offset from a 2.2 GHz carrier, so the divided output at 137.5 MHz is roughly minus 138 dBc per hertz at the same offset, subject to the divider's own noise floor. Whether that matters depends on the receiver: a narrowband system at 137.5 MHz usually cares, and the divider is the cheapest phase noise in the whole chain.

DividerLowest output from a 2.2 GHz VCOLevel relative to the VCO
12200 MHz0 dB
21100 MHzMinus 6 dB
4550 MHzMinus 12 dB
8275 MHzMinus 18 dB
16137.5 MHzMinus 24 dB

The in band noise floor is set by the division ratio

The normalized phase noise floor of the synthesizer is minus 148 dBc per hertz at 1 MHz offset from a 2.2 GHz carrier, and the in band figure at the output is that floor plus 20 log N, where N is the total division ratio. Running 4400 MHz from a 25 MHz phase detector means N is 176, which is 44.9 dB, so the in band noise lands near minus 103 dBc per hertz before the low noise mode improves it. Raising the phase detector frequency lowers N and the in band noise with it, up to the 110 MHz class limit of the part, and that is the single most effective change available on a board that measures too much close in noise.

Prescaler, mute and the auxiliary output

The dual modulus prescaler is 4/5 or 8/9, and the choice affects the minimum N and therefore the highest phase detector frequency usable at a given output. The RF output can be muted from a pin or over the serial interface, which is how a transmitter is turned off between bursts without removing the supply, and there is an auxiliary output that can be powered down when unused. Cycle slip reduction and a switched bandwidth fast lock mode shorten lock time, which matters in a frequency hopping system where the settling time, not the phase noise, sets the hop rate.

Sourcing a synthesizer with a defined VCO band

The substitution question here is the VCO band and the divider set, not the package, because a part with a different VCO range reaches different frequencies with a different noise profile. The RF component sourcing page covers the synthesizer class, the obsolete RF part replacement page covers the end of life route, and the component lead time solutions page covers allocation.