ADM7172ACPZ-R7
Product Specifications
ADM7172ACPZ-R7
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The ADM7172ACPZ-R7 from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
ADM7172ACPZ-R7: Two Amps in an 8-Lead LFCSP Is a Copper Question Before It Is an Electrical One
The ADM7172 delivers 2 A from a 2.3 V to 6.5 V input with 5 uV rms of output noise, 60 dB of rejection at 100 kHz and a 172 mV dropout at 2 A into a 3 V output, all in an 8-lead 3 mm by 3 mm LFCSP. Those are real numbers, but they are not simultaneous with every operating point. From 5 V in to 1.2 V out at 2 A the part dissipates 7.6 W, which no 3 mm by 3 mm body can pass to a board, and from 5 V to 3.3 V at 2 A it is 3.4 W, which needs a thermal pad tied to a real copper area rather than to a via or two.
Noise, rejection and what they buy at the converter
Five microvolts rms over the 100 Hz to 100 kHz band is 0.065 of a step for a 16-bit converter on a 5 V range, so the regulator is not the accuracy limit even for a 16-bit part. Rejection of 60 dB at 100 kHz means 100 mV of ripple on the input arrives as 100 uV, and the rejection falls as frequency rises, which is why a switching converter upstream is usually followed by a ferrite and this regulator rather than by this regulator alone. The noise figure is quoted independently of the output voltage, so a 1.2 V rail is as quiet as a 5 V rail, which is not true of every low noise regulator.
| Input to output | Dissipation at 2 A | Dissipation at 1 A |
|---|---|---|
| 5 V to 3.3 V | 3.4 W | 1.7 W |
| 5 V to 1.8 V | 6.4 W | 3.2 W |
| 5 V to 1.2 V | 7.6 W | 3.8 W |
| 3.3 V to 1.8 V | 3.0 W | 1.5 W |
| 3.3 V to 1.2 V | 4.2 W | 2.1 W |
Transient response is the reason to choose it
The published load transient response is 1.5 us for a 1 mA to 1.5 A step, with the output deviation quoted as a percentage of the set point in the transient table. That is a load step of three orders of magnitude in a microsecond, which is what a digital core does when it wakes from a sleep state. A regulator with the same noise but a slower loop needs more output capacitance to hold the same deviation, and more capacitance moves the loop, so the 4.7 uF ceramic the data sheet asks for is a feature rather than a restriction.
Soft start, shutdown and the sense pin
A 1 nF capacitor on the soft start pin gives a 1 ms start up, and the inrush into a 4.7 uF output is then set by that ramp rather than by the current limit. Quiescent current is 0.7 mA with no load and 0.25 uA in shutdown, which is 6.1 mAh over a year at the idle figure and 2.2 mAh in shutdown, so a battery product that leaves this rail enabled pays for it. The SENSE pin has to be connected at the load rather than at the regulator, otherwise the load regulation the part is capable of is spent in the trace.
Second sourcing a 2 A low noise regulator
The substitution question for this part is thermal first, noise second and package third, because a smaller body with the same current rating is not a drop in replacement at 2 A. The power management cross reference page covers the family, the pin to pin cross reference page covers the footprint, and incoming checks follow the incoming inspection plan.