Contact Us

HMC7950

Brand: Analog Devices
Analog Devices HMC7950 is a analog & mixed-signal component designed for Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

HMC7950 — Analog & Mixed-Signal ICs | Superb Automation

HMC7950

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The HMC7950 from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

HMC7950: 2 GHz to 28 GHz at 2.0 dB noise figure and 0.32 W of DC

The HMC7950 is a gallium arsenide pHEMT low noise amplifier covering 2 GHz to 28 GHz with 15 dB of gain, 2.0 dB of noise figure, 26 dBm of output third order intercept, 16 dBm at one decibel compression and 19.5 dBm saturated, from a single 5 V supply at 64 mA. It comes in a 6 mm by 6 mm, 16-terminal ceramic leadless chip carrier, is matched to 50 ohm and dc blocked at both ports, and has a second gate, VGG2, that works as a gain control. The supply is single polarity, so the only rail on the board is the one that sets the current.

Published values

ParameterValue
Frequency range2 GHz to 28 GHz, specified in three slices
Gain15 dB typical
Noise figure2.0 dB typical
Output power at 1 dB compression16 dBm typical
Saturated output power19.5 dBm typical
Output third order intercept26 dBm typical
Supply5 V at 64 mA, self biased
Gain controlVGG2 second gate
Package6 mm by 6 mm, 16-terminal LCC ceramic
Matching50 ohm, dc blocked input and output

2.0 dB of noise figure is worth more than 15 dB of gain

A first stage with 2.0 dB of noise figure is a noise factor of 1.58. Whatever follows it is divided by the gain in front of it, so a second stage at 2.0 dB behind 15 dB of gain adds 1.58 minus one, divided by 31.6, which is 0.018 of noise factor, or about 0.08 dB. The first stage is nearly the whole system figure, which is why the 2.0 dB number and not the 15 dB number is what a receiver chain is bought for.

That also means the loss between the antenna and this part is the most expensive copper on the board. A 1 dB pad ahead of the amplifier adds 1 dB to the system noise figure directly. A switch with 1.2 dB of insertion loss does the same. The 15 dB of gain buys nothing back in the receive path, because it comes after the noise has already been added.

5 V at 64 mA, and 0.28 W to remove from a ceramic package

5 V at 64 mA is 0.32 W of DC. At the 16 dBm compression point the output is 40 mW, so 0.28 W is dissipated. That is small enough that a ceramic leadless carrier on a via field handles it, and it is large enough that the temperature coefficient of the gain matters: 15 dB of gain that moves with die temperature moves the level at the detector behind it unless there is an automatic gain control loop.

The package is 36 square millimetres for a die that could be a fraction of that, which is the price of handling and of a 50 ohm transition at 28 GHz without wire bonding in the assembly flow. For a wideband receiver front end that is usually the right trade, because the alternative is a die attach and a ribbon bond at every channel on a multi channel board.

VGG2 as a gain control, and what it does to the noise figure

The second gate is brought out so the gain can be reduced without a PIN diode attenuator in front of the amplifier. That is useful in a receiver that has to survive a strong signal nearby without saturating the stages behind the first one. The cost is that reducing the gain by lowering VGG2 changes the bias point of the first transistor, and the noise figure degrades as the gain comes down.

For a protection function that is acceptable, because the alternative is a blocked receiver. For a level control that runs continuously it is not the right method, because the noise figure at the low gain setting is what the system has to live with whenever the control is active. A step attenuator with its own switch before the amplifier is the expensive answer and the one that keeps the noise figure at 2.0 dB in every state.

The pages that answer this most often are the RF component sourcing page for the family alternatives, the LNA selection guide for the acceptance test, and how to choose an RF amplifier for the case where a replacement has to be fitted before the next build.

Two questions buyers ask

Does the HMC7950 need a negative supply? No. It is self biased from a single 5 V rail at 64 mA. VGG2 is a control input, not a bias rail that has to be sequenced against the drain.

Is the gain control usable as a level control? It works as a protection against a strong nearby signal. As a continuous level control it degrades the noise figure whenever it is active, so a step attenuator ahead of the part is the better choice for that job.