Contact Us

LT3956EUHE#TRPBF

Brand: Analog Devices
Analog Devices LT3956EUHE#TRPBF is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

LT3956EUHE#TRPBF — Analog & Mixed-Signal ICs | Superb Automation

LT3956EUHE#TRPBF

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The LT3956EUHE#TRPBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

LT3956EUHE#TRPBF: 250 mV of High Side Sense and the Resistor It Sets

The LT3956 is a DC to DC converter built to work as a constant current source and a constant voltage regulator at the same time, with an internal 84 V, 3.3 A N channel switch. It runs from 4.5 V to 80 V, senses LED current on the high side at a 250 mV threshold, and can be configured as a boost, buck mode, buck boost, SEPIC or flyback converter. The 3000:1 True Color PWM dimming range is the figure most often quoted.

The sense threshold is the first decision

250 mV across the sense resistor means the resistor value follows directly from the current wanted: 1 A needs 0.25 ohm and dissipates 0.25 W, while the full 3.3 A switch current through the same resistor is 0.82 W. That loss sits in series with the LED string and is usually the second largest term after the switch. A 100 mV threshold would cut it to 0.33 W at 3.3 A, but the amplifier offset becomes a larger fraction of the threshold, which is why the vendor chose 250 mV and why lower current strings use a larger resistor rather than a lower threshold.

Dimming, protection and topology

3000:1 dimming at 100 Hz means the shortest on pulse is 3.3 us, and at 200 Hz it is 1.67 us. That is the range in which the LED current has to settle, so the inductor and the output capacitor set the achievable contrast rather than the controller alone. Open LED protection uses the FB pin against a programmed overvoltage, and the internal switch is rated 84 V so an 80 V output leaves only 4 V of margin for ringing; the switch rating of 84 V at 3.3 A is a ceiling of 277 W that the package can only carry in pulses. A PWM disconnect switch driver turns the string fully off, which is what removes the last of the leakage light.

Input range4.5 V to 80 V
Outputup to 80 V, constant current and constant voltage loops
Internal switch84 V, 3.3 A N channel
Current sense250 mV high side threshold, CTRL pin trims it
Dimming3000:1 True Color PWM, analogue trim on CTRL
Topologiesboost, buck mode, buck boost, SEPIC, flyback
Switching frequency100 kHz to 1 MHz adjustable
Protectionopen LED, programmable undervoltage lockout with hysteresis, soft start
Shutdown currentbelow 1 uA
Package36 lead 5 mm by 6 mm QFN

Where it fits

Automotive and industrial lighting where the string voltage is above the input, architectural and machine vision illumination that needs deep dimming, and any application where the same converter has to hold a current through a string whose forward voltage moves with temperature. Medical examination and surgical lighting fall in the same group, because a current regulated string does not change colour with forward voltage drift the way a voltage driven one does.

Order code and availability

EUHE is the industrial grade in the 5 mm by 6 mm QFN, whose exposed pad is the only heat path for the switch. The converter family is on the analogue and mixed signal line card.

Common questions

Can the part drive a string below its input voltage? Yes, buck mode is one of the supported topologies, so a 24 V input can drive a 12 V string. The catch is that the high side sense and the FB protection both have to be rechecked for the lower output.

What limits the 3.3 A switch rating? The die and the package. At 80 V and 3.3 A the instantaneous dissipation is high, so the switch rating is a pulse capability, and a continuous 3.3 A through the internal FET in a 5 mm by 6 mm body is a thermal question answered by the board copper.

LED driver comparisons sit on the power management cross reference page, and shortage alternatives are on the BOM shortage recovery page.

Request Quote — In Stock, 100% New & Original, Full Warranty