LT3502EMS#TRPBF
Product Specifications
LT3502EMS#TRPBF
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The LT3502EMS#TRPBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
LT3502EMS#TRPBF: 40 V In, 3.3 V Out, and 75 ns of On Time
The LT3502EMS#TRPBF is the 1.1 MHz member of the LT3502 family: a current mode step-down converter with a 500 mA internal switch, a 3 V to 40 V input range, an 800 mV feedback pin and an internal boost diode, in a 10-lead MS10 package. The order code reads MS for that package, TR for tape and reel and PBF for lead free. The question buyers ask first is not the headline current. It is whether the part holds regulation at the top of the input range, and at 40 V that depends on switch on time rather than on output current.
The on time that decides the ratio
At 40 V in and 3.3 V out the duty cycle is 8.25 percent. At the 1.1 MHz switching frequency the period is 909 ns, so the internal switch is on for 75 ns in every cycle. The 2.2 MHz LT3502A asks for 37.5 ns at the same ratio, which is a different demand on the minimum on time printed in the electrical table. At 24 V input the same 3.3 V output needs 125 ns, twice the room, and that is the difference between a ratio that works and one that has to be checked before the board is released.
| Topology | Current mode step-down, 500 mA internal switch |
| Input range | 3 V to 40 V |
| Switching frequency | 1.1 MHz (LT3502), 2.2 MHz (LT3502A) |
| Feedback voltage | 800 mV, external divider sets the output |
| Duty at 40 V to 3.3 V | 8.25 percent, 75 ns on time |
| Duty at 24 V to 3.3 V | 13.75 percent, 125 ns on time |
| Shutdown current | Under 2 uA, 80 uW at a 40 V rail |
| Packages | 10-lead MS10 and 8-lead 2 mm by 2 mm DFN |
Inductor, ripple and input current
With a 10 uH inductor the ripple at 3.3 V out and 40 V in works out to 0.275 A, which is 55 percent of the 500 mA switch rating. The inductor therefore carries a peak current well above the output number, and a 22 uH part halves the ripple at the cost of board area and a slower loop. The internal boost diode removes one external component, but it is a diode rather than a synchronous switch, so the efficiency figure moves with the input voltage and the same load from 3.6 V is a different thermal case than from 24 V.
The input side is often misread. Five hundred milliamps at 3.3 V is 1.65 W. At 85 percent efficiency the converter draws 1.94 W, which is 80.9 mA from a 24 V rail. That number decides the input capacitor ripple current and the trace width, not the 500 mA label. The 800 mV feedback pin means the divider ratio for 3.3 V is 4.125 to 1, so the divider current sets the stand by loss and should be chosen against the 2 uA shutdown figure rather than by habit.
Where this converter fits
The wide input range is what puts it on 24 V industrial rails, wall transformer outputs and automotive batteries, and the constant frequency above the AM band is why the 2.2 MHz version is chosen for radio-adjacent boards. With a 40 V ceiling and a 500 mA switch it suits housekeeping rails, gate drive bias, sensor supplies and stand by rails rather than a main processor rail. Frequency foldback and cycle-by-cycle current limit protect a shorted output, and the soft start pin is driven through an external RC to hold the input current surge down at plug in.
Two questions buyers ask
Can the same board run 40 V to 3.3 V at 2.2 MHz?
That ratio asks for 37.5 ns of on time. The 1.1 MHz version asks for 75 ns and leaves more margin, so a 40 V to 3.3 V rail is normally built on the 1.1 MHz part unless the minimum on time in the electrical table is checked first. Swapping to the faster part for a smaller inductor without that check is how a board ends up in pulse skipping at high line.
What actually limits the output current?
The internal switch and the cycle-by-cycle current limit, not the 500 mA in the title. At low input voltage the input current needed for a 500 mA load climbs toward the switch limit, so the deliverable output falls as the input falls. A 3.6 V input is the hard case, a 24 V input is the easy one.
Ordering and supply
The LT3502EMS#TRPBF is the MS10, tape and reel, lead free code. The DFN version carries a DC suffix and a different thermal pad, so a reel cannot be swapped between the two footprints without a board change. Grade letters and package codes are where most cross reference errors start, and the substitute has to match package, frequency option and feedback arrangement rather than only the part family.
We hold and source this family for production and for repair quantities. Start from the family page for analog mixed signal ICs, check a proposed alternative against the power management cross reference, and if the line is down send the shortage list through BOM shortage recovery so the substitutes are checked against the real board rather than the catalogue.
Request Quote — In Stock, 100% New & Original, Full Warranty