Contact Us

LT3652IMSE#TRPBF

Brand: Analog Devices
Analog Devices LT3652IMSE#TRPBF is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

LT3652IMSE#TRPBF — Analog & Mixed-Signal ICs | Superb Automation

LT3652IMSE#TRPBF

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The LT3652IMSE#TRPBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

LT3652IMSE#TRPBF: A Charger That Regulates Its Input, Not Just Its Battery

The LT3652 is a complete monolithic step down battery charger that runs from 4.95 V to 32 V (40 V absolute maximum), charges at up to 2 A, and programs a float voltage up to 14.4 V with a resistor divider for Li-Ion, LiFePO4 or SLA chemistries. Its distinguishing block is an input voltage regulation loop: when the input falls below a programmed level the charger reduces charge current, which is what makes a solar panel sit at its peak power point instead of collapsing.

Why the input loop matters

A solar panel has a knee. A charger that draws its full 2 A regardless of input voltage pulls the panel below the knee and the panel delivers less than it could. The LT3652 compares the input against a divider and backs the current off before that happens, so the panel stays on the plateau. That is peak power tracking done with a resistor divider rather than a microcontroller, and it costs no firmware.

The power arithmetic is straightforward: 2 A into a 14.4 V battery is 28.8 W, which from an 18 V panel is 1.6 A of input current plus the converter loss. Sizing the panel below that leaves the charger in current limit all day and the input loop never acts, which is the usual reason a solar build underperforms.

Float accuracy and termination

Float voltage accuracy is 0.5 percent, which on 14.4 V is 72 mV. That matters for LiFePO4, where a 4S pack floats at 14.4 V and a 72 mV error is inside the cell tolerance but leaves little room, and it matters more for Li-Ion where the float voltage sets the state of charge directly. Charge current accuracy is 5 percent and the C/10 detection is 2.5 percent, so on a 2 A charge the termination point is 200 mA with 5 mA of uncertainty. Termination can be C/10 or an on board timer, and the binary coded open collector status pins report charge and fault states without a processor.

Input range4.95 V to 32 V, 40 V absolute maximum
Charge currentup to 2 A, programmable
Float voltageup to 14.4 V by resistor divider, Li-Ion, LiFePO4, SLA
Float accuracy0.5 percent, charge current 5 percent, C/10 detection 2.5 percent
Input regulationpeak power tracking loop, threshold set by a divider
TerminationC/10 or on board timer
Switching frequency1 MHz fixed
Statusbinary coded open collector pins
Extrasno input blocking diode needed below a 4.2 V battery
Package12 lead 3 mm by 3 mm DFN and MSOP with exposed pad

Where it fits

Solar powered instruments, remote sensors, off grid lighting and any charger whose source is a panel rather than a wall adapter. It also suits a current limited adapter, because the input loop protects the source even when the source is a small wall wart rather than a panel.

Order code and availability

IMSE is the industrial grade in the MSOP with the exposed pad. The charger family is on the analogue and mixed signal line card.

Common questions

Does the input loop replace a maximum power point tracker? It performs the same job for a panel whose knee is stable, because it holds the panel voltage at a programmed level. It does not sweep the curve, so a panel with a moving knee under partial shading will not track as well as a sweeping tracker.

Can it charge a 6 cell lead acid pack? The float divider goes to 14.4 V, so a 12 V nominal lead acid pack is inside the range. A 24 V pack is not, and the input range does not change that.

Is the 1 MHz frequency a problem for EMI? It sets the harmonic positions, and the small inductor that 1 MHz allows is the reason the part fits in a 3 mm by 3 mm package. The input filter starts from 1 MHz rather than from a variable.

Battery management parts are grouped on the power management cross reference page, and cost paths for the same function are on the component cost reduction page.

Request Quote — In Stock, 100% New & Original, Full Warranty