LTC1261LIMS8#TRPBF
Product Specifications
LTC1261LIMS8#TRPBF
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The LTC1261LIMS8#TRPBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
LTC1261LIMS8#TRPBF: A Regulated Negative Rail From a Single Positive Supply
The LTC1261LIMS8#TRPBF is a switched capacitor voltage inverter that produces a regulated negative output from a single positive supply, in an 8-lead SO package. The family takes 3 V to 8 V in, produces an adjustable output from minus 1.25 V to minus 8 V or a fixed minus 3.5 V, minus 4 V, minus 4.5 V or minus 5 V set by an on-chip resistor string, draws 600 uA of quiescent current in operation and 5 uA in shutdown, and quotes 5 mV of typical output ripple. A REG pin pulls low when the output is within 5 percent of its set value, and the circuit needs three or four external capacitors depending on the version.
A negative rail is what an analogue front end needs when its signal swings below ground: a plus or minus 5 V operational amplifier, a GaAs FET bias, or a bias for a sensor that is referenced to a negative potential. Generating it with a charge pump rather than a magnetic converter is a board area decision, and this family is the small, quiet end of that market.
Twelve milliamps and the efficiency that comes with it
The family text quotes 12 mA of output current with 5 percent regulation, while the feature list on the same page says up to 15 mA. The two numbers are not the same guarantee, and the one to work with is the lower: 12 mA at minus 5 V is 60 mW, and at 15 mA it would be 75 mW. The difference is the regulator's ability to hold 5 percent at the higher current, which is the specification the REG pin is watching.
An inverting charge pump has an ideal efficiency of the output magnitude divided by the sum of the output magnitude and the input, so minus 5 V from 3 V is 62.5 percent before losses. At 60 mW of output that is 96 mW of input, or 32 mA drawn from the 3 V rail. The 600 uA of quiescent current at 3 V is 1.8 mW, which is 3 percent of the input power at full load and 30 percent at a 1 mA output, so a light load is where the quiescent current dominates and the efficiency falls away.
| Input | 3 V to 8 V single supply |
| Output | Minus 1.25 V to minus 8 V adjustable, or minus 3.5 V, 4 V, 4.5 V, 5 V fixed |
| Output current | 12 mA with 5 percent regulation, 15 mA quoted in the feature list |
| Output power | 60 mW at minus 5 V and 12 mA, 75 mW at 15 mA |
| Efficiency | 62.5 percent ideal for minus 5 V from 3 V, so 32 mA of input current |
| Quiescent current | 600 uA, 1.8 mW at 3 V, 5 uA in shutdown, 43.8 mAh a year |
| Ripple | 5 mV typical, 0.1 percent of a 5 V output |
| Regulation flag | REG pulls low within 5 percent, a 250 mV window at minus 5 V |
| External parts | Three or four 0.1 uF capacitors, plus bypass |
| Package | 8-lead SO, with a 14-lead version for the wider input range |
The 8-pin version and the 14-pin version are not the same circuit
The 14-pin member runs from 3 V to 8 V and uses one or two 0.1 uF flying capacitors depending on the input voltage, so a 3 V input needs both. The 8-pin member is optimised for a 5 V or higher input or for low output magnitudes and needs a single flying capacitor. A board laid out for one and populated with the other will have an unconnected capacitor and a floating pin, and the output will be low and noisy rather than absent, which is the hardest kind of failure to diagnose.
The REG pin is the diagnostic that makes this family usable. It pulls low when the output is within 5 percent, so firmware can wait for the negative rail before enabling the amplifier that depends on it. A board that enables a plus or minus 5 V amplifier at the same time as the inverter sees the amplifier run on a rail that is still rising, which produces a pop in an audio path and a latch condition in some operational amplifiers.
Two questions buyers ask
Can it produce minus 12 V?
No, the adjustable range stops at minus 8 V, which is the limit of the internal switch network rather than of the regulation. A minus 12 V rail from a 5 V input needs a magnetic inverting converter, and the choice between the two is ripple and size against the simplicity of a capacitor only circuit.
How much output capacitance is needed?
The data sheet specifies the input and output bypass capacitors separately from the flying capacitors, and the ripple figure assumes them. Reducing the output capacitor raises the ripple above 5 mV and moves the loop, so a board that is short of space should expect a trade rather than a free reduction. The optional compensation capacitor at the adjust pin is the other control, and it reduces ripple at the cost of settling time.
Ordering and supply
The IM8 suffix is the 8-lead SO package in tape and reel and the L is the lower current member of the family. Substitution traps are the current rating, the flying capacitor count and the fixed output option: a part with a 20 mA rating and a different pinout is not a drop in, and a fixed minus 5 V part cannot be adjusted to minus 4 V without a different order code.
We hold and source this family for production and repair lots. Start at the analog mixed signal ICs family page, compare a candidate against the power management cross reference, and where a converter has to be changed on an existing board, the order in how to verify a drop in replacement covers the capacitor count and the current rating before the rail is measured.
Request Quote — In Stock, 100% New & Original, Full Warranty