Contact Us

LT4363IMS-2#TRPBF

Brand: Analog Devices
Analog Devices LT4363IMS-2#TRPBF is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

LT4363IMS-2#TRPBF — Analog & Mixed-Signal ICs | Superb Automation

LT4363IMS-2#TRPBF

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The LT4363IMS-2#TRPBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

LT4363IMS-2#TRPBF: The 50 mV Sense That Sets the Current Limit

The LT4363 is a high voltage surge stopper that regulates the gate of an external N channel MOSFET so a load keeps running while an overvoltage is dropped across the pass device. It works from 4 V to 80 V, survives surges above 80 V with the VCC clamp, limits current by holding 50 mV across an external sense resistor, and protects against reverse input to minus 60 V. The -2 order code restarts automatically after a fault, at less than 1 percent retry duty cycle.

Current limit is a resistor choice, not a part choice

The internal amplifier holds 50 mV across the sense resistor, so the limit is set by the shunt: 5 milliohms gives 10 A, 10 milliohms gives 5 A and 20 milliohms gives 2.5 A. That is the first decision on the board, because the same controller covers a 2 A line card and a 10 A industrial rail. The overcurrent response is faster than 5 us, which is the window in which the pass FET has to absorb the fault.

During an overvoltage the FET carries the difference between the surge and the clamp. At an 80 V clamp with 5 A flowing, the device dissipates 400 W for the length of the fault timer, and 2 mJ of energy in 5 us. The timer is inversely proportional to the stress across the MOSFET, so a mild overvoltage is allowed to last longer than a severe one; the FLT pin pulls low before the timer expires, which gives the downstream logic a warning before power is removed.

Retry duty and reverse protection

The -2 version retries with less than 1 percent duty cycle, so a permanent fault at 80 V and 1 A averages 0.8 W in the pass device instead of latching the card off. The -1 version stays off until it is reset, which is the right choice when a supervisor must decide whether to power the load again. Both monitor the input with two precision comparators for undervoltage and overvoltage, and back to back FETs can replace a Schottky diode for reverse input protection, which removes the diode drop from the efficiency budget. Shutdown current is 7 uA and the shutdown pin itself withstands minus 60 V to 100 V.

Operating range4 V to 80 V, surges above 80 V with the VCC clamp
Current limit50 mV across an external sense resistor, 10 A at 5 milliohms
Overcurrent responsefaster than 5 us
Reverse protectionminus 60 V on the input, shutdown pin minus 60 V to 100 V
Fault behaviouradjustable timer, FLT warning before turn off
Restart-2 automatic retry below 1 percent duty, -1 latched
Comparatorsadjustable undervoltage and overvoltage thresholds
Shutdown current7 uA
Package12 lead DFN 4 mm by 3 mm, 12 lead MSOP, 16 lead SO

Where it fits

Industrial and automotive 12 V and 24 V inputs that see load dump, avionic 28 V buses, telecom line cards and any front end where a transient must be absorbed without dropping the load. The 4 V minimum operating voltage is worth noting: a 5 V rail sits only 1 V above the floor, so a 5 V system needs the thresholds checked against the tolerance band rather than assumed.

Order code and availability

IMS-2 is the industrial grade in the MSOP body with the automatic retry behaviour. The family and its neighbours are listed on the analogue and mixed signal line card.

Common questions

Can the sense resistor be placed on the low side? The part senses the drop between SNS and OUT, which is the high side path through the pass FET. A low side shunt is not the connection the internal amplifier is built around, so the limit would not be the 50 mV figure.

What sets the fault timer? An external capacitor on the timer pin, sized against the stress the FET can absorb. Sizing it for a 1 A load and then running 5 A through the same board is the usual mistake, because the timer allows a longer event at low current than at high current.

Input protection parts are grouped on the power management cross reference page, and socket checks before a swap are on the pin to pin page.

Request Quote — In Stock, 100% New & Original, Full Warranty