Contact Us

HMC732LC4BTR

Brand: Analog Devices
Analog Devices HMC732LC4BTR is a analog & mixed-signal component designed for Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

HMC732LC4BTR — Analog & Mixed-Signal ICs | Superb Automation

HMC732LC4BTR

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The HMC732LC4BTR from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

HMC732LC4B: 6 to 12 GHz at +1 dBm, With a 2:1 Load Requirement Written Into the Spec

The HMC732LC4B is a wideband voltage controlled oscillator with a buffer amplifier, tuning from 6 GHz to 12 GHz, running from a single +5 V supply at 57 mA and delivering about +1 dBm. Its phase noise is -95 dBc/Hz at 100 kHz offset and -65 dBc/Hz at 10 kHz, and its tuning port takes 0 V to +23 V. The footnote on the electrical table is the part that gets missed: a load standing wave ratio of 2.0 to 1 or better, across 0.01 GHz to 14 GHz, is required for proper operation. That turns the load into part of the specification.

The load is inside the specification

An oscillator that pulls 7 MHz peak to peak into a 2:1 mismatch will pull further into a worse one, and a filter that looks like 3:1 in its stop band is a common load in a real radio. The safe arrangement is a pad or an isolator between the oscillator and whatever follows, because a 3 dB pad costs 3 dB of a +1 dBm output and buys back stability that cannot be recovered any other way. Putting the oscillator straight into a switched filter bank, which is the natural temptation in a multi band synthesizer, is exactly the case the footnote warns about.

Values from the data sheet

ParameterValueNote
Frequency range6 GHz to 12 GHzContinuous tuning, no band switching inside the part
Output power+1 dBm typicalLow; a buffer amplifier follows in most radios
Phase noise-65 dBc/Hz at 10 kHz, -95 dBc/Hz at 100 kHzAbout 5 dB better than the 10 to 20 GHz part at 100 kHz
Tuning voltage0 V to +23 VSame loop supply problem as any wideband oscillator
Pulling7 MHz peak to peak into 2:1Sets the pad or isolator requirement
Drift0.4 MHz per degree C at 6 GHz, 0.25 at 12 GHzOpen loop movement of 24 MHz over 60 degrees

Drift is larger at the bottom of the band

Because the drift is quoted at both ends, the numbers show that the low end of the band moves faster in absolute terms than the high end, 0.4 MHz per degree C against 0.25. Over a 25 C to 85 C excursion that is 24 MHz at 6 GHz. A loop that can capture 24 MHz of offset at cold start needs either a search routine or a loop filter with a wide enough pull in range, and the search routine is usually cheaper than the filter.

One part for two bands is the attraction

Covering 6 GHz to 12 GHz with one oscillator removes a band switch, a second loop filter and a second set of calibration constants. The price is paid in phase noise, which is a few dB worse than a narrowband oscillator at the same frequency, and in output power, which is low enough that the buffer after it is not optional. In a link where the phase noise budget is tight at 12 GHz, a narrowband oscillator with a doubler is often the better answer despite the extra components.

Replacement and procurement

A replacement oscillator has to match the band, the tuning voltage ceiling, the output power and the load tolerance, and the last of those is the one that no data sheet comparison table carries. The RF component sourcing page lists the family, the obsolete RF part replacement page covers end of life cases, and footprint checks are on the pin to pin cross reference page.