AD8561ARZ-REEL
Product Specifications
AD8561ARZ-REEL
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The AD8561ARZ-REEL from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
AD8561ARZ-REEL: 7 ns of propagation delay is a timing budget line, not a speed badge
The AD8561ARZ-REEL is a single comparator with 7 ns of propagation delay at a 5 V single supply, in the 8-lead narrow SOIC. Its input and output sections have separate supplies, so the input stage can run from plus or minus 5 V while the output drives 5 V logic, and its common mode range includes the negative rail. It shares the LT1016 pinout with lower supply current and a wider input range.
What the vendor publishes
| Parameter | Value |
|---|---|
| Propagation delay | 7 ns at a 5 V supply |
| Supply | 3 V to 10 V single, separate input and output supplies |
| Input stage | plus or minus 5 V dual supply capable |
| Common mode | includes the negative rail |
| Latch | output hold function |
| Delay matching | rising and falling delays matched and tracking over temperature |
| Pinout | same as the LT1016, lower supply current, wider common mode |
| Temperature | -40 to +85 C |
| Packages | 8-lead SOIC, 8-lead TSSOP, 8-lead DIP |
Seven nanoseconds against the clock in front of it
At 100 MHz a period is 10 ns, so 7 ns of delay is 70 percent of it. At 50 MHz it is 35 percent, and at 10 MHz it is 7 percent. Delay alone is rarely the problem, because a constant delay can be budgeted. What matters in clock recovery and clock distribution is that the rising and falling delays match, since their difference is duty cycle error after the comparator. A part with 7 ns of delay and 1 ns of mismatch gives a worse clock than one with 9 ns and 0.2 ns, and the data sheet is the only place that difference is visible.
The same number sets the shortest pulse the part can pass. A delay of 7 ns plus a rise time of 7 ns means a pulse shorter than about 14 ns may never appear at the output. In a line receiver that is a useful filter, since noise spikes narrower than that are rejected. In a timing channel where the pulses are the information, it is a limit on the input signal, not a safety margin.
The latch pin, and why a fast comparator still chatters
The latch holds the output in its present state while asserted. That is what makes a comparator usable as a sampling element: the input can move while the decision is being captured, and the output does not follow. It is also the standard cure for the last problem of any fast comparator, which is that an input parked on the threshold with a few microvolts of noise produces a burst of edges at the output.
Hysteresis is the other cure, and this part does not publish one. If the application compares a slowly moving signal, such as a supply rail crossing a threshold or a photo diode behind an amplifier, positive feedback from the output to the non inverting input is added on the board. Without it the output toggles at the frequency of whatever noise sits on the input, and the counter behind it reads nonsense.
Where the split supplies earn their place
Separate input and output supplies let a plus or minus 5 V analog front end talk to 3.3 V or 5 V logic without an external level shifter, and the common mode range that includes the negative rail means a signal swinging below ground does not have to be offset first. A 12-bit converter at a 2.5 V reference has a 610 microvolt LSB, so a comparator offset in the low millivolts is a handful of counts, and the offset of the part is a line item in the error budget rather than an afterthought.
Two questions buyers ask
Is it a drop in for the LT1016? The pinout is the same and the supply current is lower, and the input common mode range is wider because it includes the negative rail. Before a swap, check the output stage type and the latch polarity on the existing board, and confirm the supply arrangement, because the two parts do not necessarily take the same output supply wiring.
Does it need a heat sink or a special board? No. Seven nanoseconds and a few tens of milliamps do not make a thermal problem. What it does need is a ground plane under the part, a short return path for the latch and output traces, and decoupling on both supplies if the split supply arrangement is used.
SUPERB quotes the AD8561ARZ-REEL against this row and offers the TSSOP and DIP packages on the same order. Comparators and amplifiers with a different speed and supply are compared under amplifier cross reference. Pin level swaps from the LT1016 are handled under pin to pin cross reference, and stock sits in the analog and mixed signal ICs index.
AD8561ARZ-REEL has no internal hysteresis, so the noise band in front of it sets the trip point
Seven nanoseconds of propagation delay is short enough that the comparator follows its own input noise. A source with 20 uV rms of noise across the 50 MHz that this part passes will cross a fixed threshold thousands of times per millisecond, and the output will chatter. A 12 bit converter on a 2.5 V reference has 610 uV per count, so 20 uV is 0.03 of a count: the noise is invisible at the converter and decisive at the comparator. The cure is hysteresis, and this part has none, which makes it an external component rather than a data sheet feature.
How much hysteresis, and what it costs in resistors
Six sigma of 20 uV is 120 uV, which is the smallest useful hysteresis for that source. Positive feedback gives a hysteresis of the output swing times the divider ratio, so on a 5 V swing 120 uV needs a ratio of 24 parts per million. With a 1 kohm resistor from the reference node, the feedback resistor is 24 milliohm, which is below the trace resistance of the board and not buildable. The practical answer at these levels is not positive feedback at all: it is a band limiting filter in front of the input, which reduces the noise instead of masking it, or the latch pin, which removes the chatter by holding the decision for a known time.
The latch pin as the timing element
The latch holds the output at the state it had when the pin was asserted. With 7 ns of delay and a 7 ns rise time, a pulse shorter than about 14 ns may never appear at the output, so the latch window has to be longer than the sum. At 50 MHz the period is 20 ns and a 14 ns window is 70 percent of it, which leaves 6 ns for the input to settle. At 10 MHz the same window is 14 percent of the period and the arrangement is comfortable. That is the trade the latch offers: a defined decision time in exchange for the duty cycle it consumes.
Split supplies, and the logic threshold on the output side
The input section runs from plus or minus 5 V and the output section from 3.3 V, which removes the level shifter that a 5 V comparator would need in front of 3.3 V logic. The 3.3 V output has to cross 2.0 V, the minimum high input of most 3.3 V families, within the 7 ns rise, and drive the input capacitance of whatever follows. A 10 pF load charged to 2.0 V is 20 pC, which at 7 ns is 2.9 mA of average drive: inside what the output stage delivers, and worth checking against the 20 mA figure before four loads are hung on one comparator.
| Source noise over 50 MHz | Six sigma | Hysteresis as a divider ratio on a 5 V swing | Feedback resistor against a 1 kohm reference leg |
|---|---|---|---|
| 5 uV rms | 30 uV | 6 ppm | 6 milliohm |
| 20 uV rms | 120 uV | 24 ppm | 24 milliohm |
| 100 uV rms | 600 uV | 120 ppm | 0.12 ohm |
| 2 mV rms | 12 mV | 2.4 per mille | 2.4 ohm |
Comparator and amplifier equivalents are listed on amplifier cross reference, the pin and grade checks before a substitution are on how to verify a drop in replacement, and the Analog Devices route is on ADI part second source.
Request Quote — In Stock, 100% New & Original, Full Warranty