Contact Us

AD8132ARZ-R7

Brand: Analog Devices
Analog Devices AD8132ARZ-R7 is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

AD8132ARZ-R7 — Analog & Mixed-Signal ICs | Superb Automation

AD8132ARZ-R7

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The AD8132ARZ-R7 from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

AD8132ARZ-R7: 350 MHz of bandwidth behind a 191 MHz full power ceiling

The AD8132 is a differential amplifier with resistor set gain, 350 MHz of minus 3 dB bandwidth, a 1200 V per microsecond slew rate, and internal common mode feedback that holds the output balance to minus 68 dB at 10 MHz. It takes a single ended or differential input and produces a differential output whose common mode is set by a voltage on a separate pin, which is what lets it drive a single supply converter without a transformer. It draws 10.7 mA from a 5 V rail and is offered in 8 lead small outline and MSOP packages over minus 40 C to plus 125 C.

What the vendor page states

ParameterValue
Bandwidth350 MHz at minus 3 dB
Slew rate1200 V per microsecond
Gainset by four external resistors
Output balanceminus 68 dB at 10 MHz, gain and phase
Distortionminus 99 dBc spurious free dynamic range at 5 MHz into 800 ohm
Common modeset by a voltage on the dedicated pin, internal feedback loop
Supply current10.7 mA at 5 V
Supply range2.7 V single supply to plus and minus 5.5 V
Packages8 lead small outline and MSOP, minus 40 C to plus 125 C
Automotivethe W suffix is AEC-Q100 qualified

Three hundred and fifty megahertz of small signal, 191 MHz of full power

The 350 MHz figure is measured on a small signal, and a large signal is limited by the slew rate instead. A 2 V peak to peak sine at frequency f needs a maximum slope of pi times f times 1 V, so 1200 V per microsecond supports 191 MHz. That is a 1.83 to 1 gap between the headline bandwidth and what the part does with a full scale signal, and a buyer comparing this part against a faster amplifier should compare the full power figure, not the small signal one. A 1 V step itself takes 0.83 ns at the quoted slew rate, so at these frequencies the edge is not the limit; the settling of the feedback loop is.

Minus 68 dB of balance is 0.04 percent

Minus 68 dB of gain and phase mismatch between the two outputs is 0.0398 percent, and it is that mismatch, not the open loop distortion, that sets the second harmonic in a single ended to differential conversion. A 1 V peak to peak carrier with minus 99 dBc of spurious content puts the largest spur at 11.2 microvolts, which on a 2 V full scale into a 16 bit converter is under one count. The balance figure is the one that holds when the part is used as an active transformer, because a single ended input reaches the output through two different resistor paths and only the internal feedback keeps them equal.

Ten point seven milliamps is 53.5 milliwatts, and the pinout pays for it

At 5 V the quiescent current is 53.5 mW, and at plus and minus 5.5 V it is 58.8 mW, which in an 8 lead small outline package is a 60 to 80 C rise on a minimal pad and rather less on a proper ground pour. A quad channel receive path built from four of these is 214 mW of standing dissipation before any signal, and that is the number that decides whether a four channel front end fits a small module. The alternate route, a transformer, has no standing current but loses the DC content of the signal, which is precisely what this part exists to keep.

The common mode pin is the reason it drives single supply converters

Setting the output common mode to 0.9 V or 1.5 V from a reference lets a differential signal ride on whatever level the converter's input stage expects, with no coupling capacitors and no level shifting stage. The internal loop that holds that level has its own bandwidth and its own settling, and it is the first thing to check when a converter's input looks noisy at low frequency: a common mode pin driven from a high impedance divider will follow the signal instead of holding still. Decoupling that pin to the same ground the converter uses is the standard cure and does not appear in any of the headline numbers.

Before the order goes out

The single channel differential driver role is also served by the rail to rail parts in the same catalogue, and the AD8132's place is the low cost, moderate bandwidth corner where its 2.7 V to plus and minus 5.5 V range covers both a 3.3 V single supply and a plus and minus 5 V analog rail. The amplifier cross reference lists the differential drivers by bandwidth and supply range, the converter cross reference lists the converters this part normally drives, and the analog and mixed signal category page holds the rest of the amplifier family.

Gain of Two Into a 14 Bit Converter: Noise, Balance and the 10.7 Milliamps

The AD8132ARZ-R7 is chosen for three properties in a converter front end: it turns a single ended signal into a differential one, it holds the output balance to minus 68 dB, and it does both at 350 MHz. The properties that decide whether a 14 bit converter keeps its 14 bits are the input noise, the resistor values that set the gain, and the current the part draws from the same rail the converter uses.

Noise at a gain of two is 1.1 LSB of a 14 bit converter

The input voltage noise is about 5.5 nV per root hertz. Over a 40 MHz band that integrates to 34.8 uV RMS at the input, and at a gain of two it is 69.6 uV at the output. A 14 bit converter on a 2 V peak to peak span has an LSB of 122 uV, so the amplifier contributes 0.57 LSB of noise and the converter's own quantisation contributes 0.29 LSB. The amplifier noise is twice the quantisation noise, which means the chain is limited by the amplifier and not by the converter, and a 16 bit converter behind the same amplifier would be limited by the amplifier by a factor of eight. Over a 10 MHz band the same amplifier gives 34.8 uV, 0.28 LSB, and the balance changes.

The feedback resistors set the bandwidth and the loading

With a gain of two the feedback resistor is twice the input resistor. A 400 ohm and a 200 ohm pair presents 600 ohm to the source and puts a pole at 1 over two pi times 400 ohm times the few picofarads at the summing node, which lands in the region of 200 MHz. Halving both resistors doubles that pole and doubles the current the amplifier delivers into the feedback network, which is where the 10.7 mA goes. Doubling both resistors halves the loading and halves the bandwidth, and a 14 bit converter sampling at 40 MSPS needs the wider of the two.

Minus 68 dB of balance is 0.04 percent

Output balance of minus 68 dB at 10 MHz is 0.04 percent of amplitude mismatch between the two outputs. A converter that samples the difference sees that as an even order distortion term at minus 68 dB, which is 11.2 effective bits at full scale. The figure is quoted at 10 MHz and it degrades with frequency, so a 40 MHz input has less balance than the headline and the even order term grows. The balance is set by the four resistors around the amplifier as much as by the amplifier, and a 0.1 percent resistor pair gives a minus 60 dB floor before the part is counted.

TermFigureAt a 2 V peak to peak spanIn 14 bit LSB of 122 uV
Input noise over 10 MHz5.5 nV per root hertz17.4 uV input, 34.8 uV output0.28
Input noise over 40 MHz5.5 nV per root hertz34.8 uV input, 69.6 uV output0.57
Output balanceminus 68 dB at 10 MHz0.04 percent mismatch11.2 effective bits
Supply current10.7 mA at 5 V53.5 mWnot a signal term
Small signal bandwidth350 MHz0.35 V peak limits slewnot a signal term

The common mode pin is what makes a single supply converter possible

The output common mode is set by a voltage on a dedicated pin with its own internal loop, so the differential output can sit at the middle of a single supply converter's input range without a transformer and without a second amplifier. The loop holds the common mode against the signal, which is why the balance figure survives a single ended input. A 5 V single supply part with a 2.5 V common mode and a 2 V peak to peak differential output has 1 V of headroom to each rail, and the 350 MHz small signal figure is not available at that amplitude: the slew rate of 1200 V per microsecond limits a 1 V peak swing to 191 MHz.

A gain of two and 53 mW in a converter front end

Ten point seven milliamps at 5 V is 53.5 mW for the amplifier, and the converter behind it draws its own current from the same rail. A four channel board with one amplifier per channel therefore spends 214 mW on drive, which is a battery question and not a signal question. The W suffix in the same family is the AEC-Q100 version, so an automotive board has to check that the order code carries it: the base ARZ part is the industrial grade and the automotive qualification is a different order code rather than a batch property.

The amplifiers and comparators on the line card are listed on the amplifiers and comparators page, with the partners on the analog and mixed-signal IC page. Where a part is short, the pin to pin cross reference page sets out which family members share a footprint and which do not.

Request Quote — In Stock, 100% New & Original, Full Warranty