Contact Us

HMC606LC5

Brand: Analog Devices
Analog Devices HMC606LC5 is a analog & mixed-signal component designed for Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

HMC606LC5 — Analog & Mixed-Signal ICs | Superb Automation

HMC606LC5

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The HMC606LC5 from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

HMC606LC5: phase noise at minus 160 dBc per hertz from a distributed amplifier

The HMC606LC5 is a gallium arsenide indium gallium phosphide HBT distributed amplifier covering 2 GHz to 18 GHz with 14 dB of gain and, according to the vendor, minus 160 dBc per hertz at a 10 kHz offset, which is the reason this part exists. An FET distributed amplifier of the same bandwidth reaches about minus 150 dBc per hertz at that offset. The improvement comes from the HBT rather than from the circuit, and it is bought with noise figure, which is 4.5 dB in the low band and 6.5 dB in the top band, and with output power, which is 18 dBm saturated.

Published values

ParameterValue
Frequency range2 GHz to 18 GHz, two bands
Gain14 dB typical, 11 dB minimum 2 to 12 GHz; 13 dB typical, 10 dB minimum 12 to 18 GHz
Gain flatnessplus or minus 1.0 dB in both bands
Gain variation over temperature0.021 dB per degree low band, 0.25 dB per degree high band
Noise figure4.5 dB typical 2 to 12 GHz, 6.5 dB typical 12 to 18 GHz
Input return loss20 dB and 22 dB across the two bands
Output return loss15 dB in both bands
Output power at 1 dB compression15 dBm typical 2 to 12 GHz, 13 dBm 12 to 18 GHz
Saturated output power18 dBm low band, 15 dBm high band
Output third order intercept27 dBm and 22 dBm
Phase noiseminus 140 dBc per hertz at 100 Hz, minus 160 at 10 kHz, minus 170 at 1 MHz
Supply5 V on VCC1 and VCC2, 64 mA typical, 95 mA maximum
Die size2.80 mm by 1.73 mm by 0.1 mm

What a ten decibel phase noise advantage is worth

Phase noise in an amplifier comes from the flicker and shot noise of the active device up converted by the signal passing through it. An HBT has a lower corner frequency than a pHEMT and a much lower low frequency noise contribution, which is why the 10 kHz offset figure improves by about ten decibels. In a radar or an instrument that uses the amplifier inside a synthesiser loop or ahead of a phase detector, that difference sets the loop bandwidth and the residual noise floor of the whole source.

The cost is that the same device has a higher noise figure and less output power than an FET part of the same bandwidth, and the two limits are not negotiable. A receiver that needs 2.5 dB of noise figure cannot use this amplifier as a first stage; a transmit chain that needs 25 dBm cannot use it as a driver. Where it wins is in the middle of a chain, after a low noise stage and before a mixer, or as a buffer inside a frequency generation block where the level is modest and the phase noise is everything.

Sixty four milliamps and the two supply pins

VCC1 and VCC2 both sit at 5 V and the part draws 64 mA typical, 95 mA maximum, which is 0.32 W to 0.48 W of DC. The dissipation is small enough that a package on a modest via field handles it, and the die at 2.80 mm by 1.73 mm has 4.84 square millimetres of area for about 0.26 W at the compression point, which is 0.054 W per square millimetre.

Two supply pins on a distributed amplifier usually mean two separate collector feeds, one at each end of the artificial transmission line, and both have to be decoupled. Decoupling one and not the other leaves half the line fed through the other half, which shows up as a tilted gain response rather than as a dead part, and it is a common assembly error on a part with two identical looking supply pins.

Forty to fifty percent gain margin over temperature

The gain variation of 0.021 dB per degree in the low band over 125 degrees is 2.6 dB, and the high band figure of 0.25 dB per degree is twelve times larger and looks like a typographical error in the vendor document. If it is real, the gain at 18 GHz moves by 31 dB across the military temperature range, which no system can absorb. The figure to work with is the low band one until the vendor confirms the high band value, and the confirmation is worth having in writing before a build is frozen.

The gain minimum of 11 dB against a typical of 14 dB is also wide. A production budget has to use the minimum, and a receiver chain planned on 14 dB will be three decibels short on the worst unit. That is a general rule for this whole family of Hittite era parts, where typical figures are comfortable and minimums are not.

For a board that has to keep running while a reel runs out, the RF component sourcing page is where the family alternatives sit, the LNA selection guide is the check list before a substitute goes in, and how to choose an RF amplifier is how a gap is covered without a new line item.

Two questions buyers ask

Is the HMC606 a low noise amplifier? No. The noise figure is 4.5 dB to 6.5 dB. It is a phase noise part, chosen for minus 160 dBc per hertz at 10 kHz rather than for sensitivity.

Can the two supply pins be fed from one rail? Yes, from one 5 V rail, but each pin needs its own decoupling close to the package, because they feed the two ends of a distributed structure.