Contact Us

ADA4851-4YRUZ-RL7

Brand: Analog Devices
Analog Devices ADA4851-4YRUZ-RL7 is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

ADA4851-4YRUZ-RL7 — Analog & Mixed-Signal ICs | Superb Automation

ADA4851-4YRUZ-RL7

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The ADA4851-4YRUZ-RL7 from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

ADA4851-4YRUZ-RL7: 130 MHz of bandwidth, 11 MHz of flatness

The ADA4851-4 is a quad voltage feedback amplifier with rail to rail outputs, 130 MHz of small signal bandwidth and a 375 V per microsecond slew rate, at 2.5 mA per amplifier. It is priced and packaged for consumer and automotive video, where the numbers that decide whether the picture is right are not the bandwidth but the 0.1 dB flatness, the differential gain and the differential phase. It runs from 2.7 V to 12 V, so it works on a single 3.3 V rail or on plus and minus 5 V, and the outputs swing to within 60 mV of either rail.

What the vendor page states

ParameterValue
Channelsfour
Bandwidth130 MHz at minus 3 dB
Slew rate375 V per microsecond
Settling55 ns to 0.1 percent
0.1 dB flatness11 MHz
Differential gain and phase0.08 percent and 0.09 degrees
Output swingwithin 60 mV of either rail
Input offset0.6 mV
Supply range2.7 V to 12 V, specified at 3 V, 5 V and plus and minus 5 V
Supply current2.5 mA per amplifier, with a power down mode
Package and grade14 lead TSSOP, minus 40 to plus 125 C, AEC-Q100 on the W suffix

Which bandwidth number belongs in the comparison

Eleven megahertz of 0.1 dB flatness against 130 MHz of minus 3 dB bandwidth is 8 percent of the headline figure. For composite video the flatness out to 5 MHz and the differential gain and phase are what a viewer sees as colour and tilt, and the 130 MHz is only there to keep the loop stable and the pulse response clean. At the 3.58 MHz subcarrier, 0.09 degrees of differential phase is 70 ps of delay, and 0.08 percent of differential gain on a 1 V peak to peak chroma signal is 0.8 mV of amplitude change between the parts of the picture that carry colour. Both are below what a monitor shows, which is why the part can be cheap and still pass.

Four amplifiers, ten milliamps, fifty milliwatts

Four channels at 2.5 mA each is 10 mA, which on 5 V is 50 mW for the whole quad, or 30 mW per amplifier at 12 V. A video chain that needs four buffers, a sync separator and a cable driver is the case this part was built for: the package holds all four and the power down mode lets the unused ones stop drawing. The 55 ns settling to 0.1 percent puts a ceiling of 18.2 MSPS on full settling applications, so this is a video and buffer part and not a driver for a 100 MSPS converter.

Rail to rail means two different things at the two ends

The output reaches within 60 mV of either rail, which on 5 V leaves 4.88 V of usable swing. The input is not rail to rail: it extends 200 mV below the negative rail and stops 2.2 V below the positive rail. On a single 5 V supply that means the input common mode tops out at 2.8 V, which is the constraint that catches a first article when a video signal is biased at mid rail and then loaded by a second stage. A buyer comparing this against a true rail to rail input part should check the input range on the actual bias point rather than on the headline.

Before the order goes out

The AEC-Q100 qualification belongs to the W suffix on the dual and quad parts, not to the plain part number, so an automotive line has to order the right suffix rather than the same speed grade. The amplifier cross reference lists the video and rail to rail alternatives by flatness and differential gain, the BOM shortage recovery page is the starting point when the 14 lead package is short, and the analog and mixed signal category page holds the rest of the amplifier family.

Request Quote — In Stock, 100% New & Original, Full Warranty