AD8610ARZ-REEL7
Product Specifications
AD8610ARZ-REEL7
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The AD8610ARZ-REEL7 from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
AD8610ARZ-REEL7: 10 picoamps into a megohm is 10 microvolts
The AD8610 is a single JFET input operational amplifier with a 100 microvolt maximum offset, 6 nV per root hertz of voltage noise and a maximum input bias current of 10 pA that the vendor states holds over the whole temperature range. That last clause is the reason the part exists. Many JFET amplifiers quote a bias current at 25 C and then double it every ten degrees, which is useless in an instrument that has to hold its zero at 85 C. This one is specified from minus 40 to plus 125 C, runs on supplies from plus and minus 5 V to plus and minus 13 V, and settles to 0.01 percent in 600 ns.
What the vendor page states
| Parameter | Value |
|---|---|
| Input bias current | 10 pA maximum |
| Input voltage noise | 6 nV per root hertz |
| Offset voltage | 100 microvolts maximum |
| Settling | 600 ns to 0.01 percent |
| Slew rate | 50 V per microsecond |
| Supply range | plus and minus 5 V to plus and minus 13 V |
| Output swing | within 1.2 V of either supply with a 1 kohm load |
| Capacitive load | stable with more than 1000 pF at unity gain |
| Stability | unity gain stable, no phase reversal |
| Package and grade | 8 lead SOIC and MSOP, minus 40 to plus 125 C |
The bias current sets the source impedance ceiling
Ten picoamps into 100 kohm is 1 microvolt, into 1 Mohm it is 10 microvolts, and into 10 Mohm it is 100 microvolts, which equals the offset ceiling. So a photodiode or an electrometer front end above a few megohms of source impedance is buying the bias current specification rather than the noise specification, and the 10 pA maximum is the number to put in the comparison table. A bipolar part with 10 nA of bias current would produce a thousand times that error on the same resistor, which is why the JFET input survives in high impedance instrumentation while faster bipolar parts take everything else.
Noise against offset, and which one is larger
Six nanovolts over a 10 kHz bandwidth is 0.6 microvolts, which is 0.6 percent of the 100 microvolt offset ceiling. For a DC instrument the offset and its drift own the error budget, and the noise only matters when the signal itself is below about a microvolt. That ordering is worth keeping straight at the buying stage, because a part with half the noise and twice the offset would be a downgrade in a weigh scale and an upgrade in a vibration sensor.
Swing, headroom and cable capacitance
With a 1 kohm load the output reaches within 1.2 V of each rail, which on plus and minus 5 V leaves 7.6 V peak to peak and on plus and minus 13 V leaves 23.6 V peak to peak. That figure decides the input range of the converter behind it and whether the part can drive a 4 V full scale part directly. At 50 V per microsecond a 10 V step takes 200 ns, so the 600 ns settling figure is dominated by the last part of the settling curve rather than by slew. The 1000 pF stability matters because the input of a shielded cable looks exactly like that, and a part that is only stable into 100 pF will ring on the first metre of wire.
Before the order goes out
The dual version is the AD8620, which shares the die but not the package, so it is not a drop in substitution for a single position. The amplifier cross reference carries the JFET input alternatives by bandwidth and bias current, the BOM shortage recovery page is where to start if this package is short, and the analog and mixed signal category page holds the rest of the precision amplifier family.
AD8610ARZ-REEL7 into a 16 bit converter: the settling figure is a 14 bit number
The amplifier is quoted at 600 ns to 0.01 percent, and 0.01 percent of a full scale is one part in 10,000, which is 6.5 codes of a 16 bit converter and 4 codes of a 14 bit one. Arithmetic on the published figure, not a new measurement: an acquisition window sized for 16 bit accuracy needs the settling to 0.0015 percent, and the data sheet does not quote that point. A 1 MSPS converter leaves one microsecond for the whole acquisition, so the honest question is not whether the amplifier settles in 600 ns but whether the last 400 ns cover the missing decade. On a 10 V full scale a 16 bit code is 152.6 uV, and 0.01 percent of 10 V is 1 mV.
| Term | Quoted figure | On a 10 V scale | In 16 bit codes |
|---|---|---|---|
| Offset voltage | 100 uV maximum | 100 uV | 0.66 LSB |
| Voltage noise to 100 kHz | 6 nV per root hertz | 1.90 uV RMS | 0.012 LSB |
| Bias current into 1 Mohm | 10 pA maximum | 10 uV | 0.066 LSB |
| Bias current into 10 Mohm | 10 pA maximum | 100 uV | 0.66 LSB |
| Settling to 0.01 percent | 600 ns | 1 mV | 6.5 LSB |
The source impedance is what decides which term dominates
Ten picoamps is nothing until it meets a resistor. Into one megohm it is 10 uV, a fifteenth of the offset limit, and into ten megohms it is 100 uV, which equals the offset limit and doubles the direct current error. That is why a photodiode or a high value bridge benefits from this part and a low impedance attenuator does not care. The 6 nV figure is also a density rather than a total: over 100 kHz it integrates to 1.90 uV, over 1 MHz to 6.0 uV, so a converter that samples at 1 MSPS without an anti-alias network behind it sees four times the figure the 100 kHz column suggests.
Supply rail choice moves the swing by a factor of three
With a 1 kohm load the output reaches within 1.2 V of each rail. On plus and minus 5 V that is 7.6 V peak to peak, and on plus and minus 13 V it is 23.6 V peak to peak, which changes what converter can sit behind the amplifier without an attenuator. The 1000 pF capacitive load stability matters on the same board: an input cable, a filter capacitor or a converter's sample network all present capacitance, and an amplifier that is stable only into 100 pF rings on the first metre of shielded wire. The unity gain stable rating and the no phase reversal behaviour are the two properties that let the same part serve a follower and a gain stage without a second order code.
The converter side of this decision is indexed on the ADC and DAC cross reference, the rest of the precision amplifier family sits on the analog and mixed-signal ICs page, and when the package rather than the part is the constraint the BOM shortage recovery route is where a replacement order starts.
Request Quote — In Stock, 100% New & Original, Full Warranty