Contact Us

HMC465-Die

Brand: Analog Devices
Analog Devices HMC465-Die is a analog & mixed-signal component designed for Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

HMC465-Die — Analog & Mixed-Signal ICs | Superb Automation

HMC465-Die

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The HMC465-Die from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

HMC465 die: a DC to 20 GHz driver that holds 10 V peak to peak

The HMC465 is a gallium arsenide pHEMT distributed driver amplifier covering DC to 20 GHz with 15 dB of gain, 3 dB of noise figure and 25.5 dBm saturated output, from a single 8 V supply at 160 mA. Alongside the power figures the vendor document lists a saturated output voltage of 10 V peak to peak in the DC to 6 GHz and 6 GHz to 12 GHz bands and 8 V peak to peak from 12 GHz to 20 GHz, with a group delay variation of plus or minus 15 picoseconds to 10 GHz. Those two rows are what separate this part from the general purpose amplifiers in the same family, and they are the rows a driver application is bought for.

Published values

ParameterValue
Frequency rangeDC to 20 GHz, specified in three bands
Gain16 dB typical DC to 6 GHz, 15 dB 6 to 12 GHz, 12.5 dB 12 to 20 GHz
Gain flatnessplus or minus 0.75 dB, 0.25 dB and 1.5 dB across the three bands
Gain variation over temperature0.015 to 0.045 dB per degree depending on band
Noise figure3.0 dB typical DC to 12 GHz, 4.0 dB 12 to 20 GHz
Input return loss20 dB, 15 dB and 8 dB across the three bands
Output return loss22 dB, 17 dB and 12 dB
Output power at 1 dB compression24 dBm, 23 dBm and 20 dBm typical
Saturated output power25.5 dBm, 25 dBm and 23 dBm
Saturated output voltage10 V peak to peak to 12 GHz, 8 V peak to peak above
Output third order intercept32 dBm, 28 dBm and 24 dBm
Group delay variationplus or minus 15 picoseconds, DC to 10 GHz
Supply8 V at 160 mA, 1.28 W of DC
Gate biasVGG1 adjusted for 160 mA, VGG2 at 1.5 V typical

Ten volts peak to peak is not a 50 ohm power figure

Ten volts peak to peak across 50 ohm would be 1 W, or 30 dBm, and the saturated output power of the same part is 25.5 dBm, which is 355 mW. The two rows cannot describe the same load, so the voltage figure belongs to a high impedance or a differential load and the power figure to a 50 ohm fixture. A buyer sizing this part as a modulator driver needs to know which one applies, because the answer decides whether the driver is followed by a 50 ohm resistor, a transformer or the capacitive gate of a modulator.

That also explains why the voltage row falls to 8 V peak to peak above 12 GHz while the power row falls only to 23 dBm. A part that is voltage limited runs out of swing before it runs out of power, and the crossover between the two limits is exactly where the top band starts to be the difficult one. On a driver for an electro optic modulator the voltage is the specification that matters, and 8 V peak to peak is the number to carry into the link budget rather than 23 dBm.

160 mA at 8 V, and why the dissipation barely moves with drive

8 V at 160 mA is 1.28 W of DC. At the saturated point of 25.5 dBm the output is 355 mW, so 0.93 W becomes heat, and at the compression point of 24 dBm it is 0.99 W. The part is therefore a nearly constant heat source: driving it harder changes the heat by less than a tenth of a watt, which is good news for the thermal path and bad news for anyone who plans to run it cool at low drive.

The other consequence is that the DC point is what a bias supply has to hold under modulation. A driver for a wideband signal draws current in bursts as the envelope moves, and the 160 mA average with a 1.28 W budget assumes the supply can deliver the peak without sagging. Decoupling close to the drain pin, sized for the lowest modulation frequency rather than the highest radio frequency, is what keeps the envelope from appearing on the drain and turning into amplitude distortion.

Group delay is the specification that wideband systems forget

Plus or minus 15 picoseconds to 10 GHz sounds small until it is converted: 15 picoseconds is about 4.5 mm of free space, and in a phased array or a two channel instrument the difference between channels is what sets the phase error at the top of the band. Two parts from different lots that both meet the gain and power limits can still differ in group delay by more than the system allows, and nothing on a scalar test bench shows it.

The measurement needs a two port network analyser with a phase reference, not a power meter, and it has to be done on the assembly because the bond wires add their own delay. For a programme that has to hold channel matching, the practical approach is to buy the parts as one lot and to measure delay on the assembled board, treating a part that falls outside as a sorting decision rather than a defect.

Buyers usually arrive at the RF component sourcing page to find the family alternatives, then use how to choose an RF amplifier to confirm a substitute before it is fitted; one stop RF supply is the routine for a part that has already stopped shipping.

Two questions buyers ask

Is the HMC465 a low noise amplifier? It has 3 dB of noise figure to 12 GHz, which is usable as a first stage, but the part is specified and priced as a driver, with 10 V peak to peak of swing and 25 dBm of saturated power.

Does it need a negative gate supply? Yes. VGG1 sits below the source to set 160 mA, and it has to be present before the drain is applied.