Contact Us

ADM485EARZ-REEL7

Brand: Analog Devices
Analog Devices ADM485EARZ-REEL7 is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

ADM485EARZ-REEL7 — Analog & Mixed-Signal ICs | Superb Automation

ADM485EARZ-REEL7

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The ADM485EARZ-REEL7 from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

ADM485EARZ-REEL7: 32 nodes on the bus, not 128

The ADM485E is a 5 V half duplex RS-485 and RS-422 transceiver with plus or minus 15 kV of human body model ESD protection on the bus pins, a 2.5 Mbps data rate, and slew rate limited driver outputs that keep radiated emissions and reflections down on a bus that is not terminated properly. It sits in an 8 lead small outline package and is the part that connects a meter, a drive or a controller to a two wire twisted pair that runs through a building. The number that decides whether it is the right part is the bus load: this one drives 32 transceivers, and two other parts in the same data sheet drive 128.

What the vendor page states

ParameterValue
StandardTIA/EIA RS-485 and RS-422 compliant
ESDplus or minus 15 kV human body model on the RS-485 input and output pins
Data rate2.5 Mbps
Duplexhalf duplex
Common mode rangeminus 7 V to plus 12 V
Bus loading32 transceivers, one unit load each
Protectionthermal shutdown and short circuit protection, three state on disable
Driveslew rate limited outputs for low emissions
Supply5 V
Package8 lead small outline, industrial temperature

Node count is a purchasing decision, not a detail

One unit load is 12 kohm, and 32 of them in parallel is 375 ohm, which is exactly the load a compliant driver is specified into. The ADM487E and ADM1487E in the same data sheet have quarter unit load receivers, so they allow 128 transceivers on the same pair with the same footprint and the same pinout. A system that specifies 32 nodes and later adds a repeater has bought the wrong suffix, and because the parts are pin compatible the mistake does not show up until the bus starts dropping frames at the far end. Buyers should decide the node count before the line is placed, not after.

2.5 Mbps against a building sized cable

At 2.5 Mbps one bit is 400 ns and a ten bit character is 4 microseconds. A 1 km run has a round trip of about 5 microseconds at two thirds the speed of light, which is 13 bit times, so on a long bus the data rate is limited by the round trip and by whether the ends are terminated, not by the driver. The slew rate limiting is what makes an unterminated stub tolerable: it slows the edges enough that the reflection settles inside the bit rather than at the receiver threshold.

The 19 volt common mode window

The receiver accepts minus 7 V to plus 12 V of common mode, a window 19 V wide. That is the specification that matters in a plant where two buildings sit on different earths and the ground potential between them moves by several volts with every motor start. A transceiver with a narrower window will latch a valid looking bit at the wrong level, and the fault looks like software until someone puts a meter between the two earths.

What the page does not promise

The ESD figure covers the bus pins, not the logic side, and the page lists no fail safe biasing on chip, so an idle bus still needs its pull up and pull down resistors or a part with that feature built in. The thermal shutdown and short circuit protection do cover a driver that is enabled into a shorted pair, which is the common field failure on a bus that is wired while energised. The pin to pin cross reference lists the transceivers that share this footprint, the obsolete part hub tracks the older 485 parts that are being replaced by this generation, and the analog and mixed signal category page holds the rest of the interface family.

Request Quote — In Stock, 100% New & Original, Full Warranty