Contact Us

HMC460LC5

Brand: Analog Devices
Analog Devices HMC460LC5 is a analog & mixed-signal component designed for Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

HMC460LC5 — Analog & Mixed-Signal ICs | Superb Automation

HMC460LC5

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The HMC460LC5 from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

HMC460LC5: 2.5 dB noise figure at 10 GHz from 60 mA

The HMC460 is a gallium arsenide pHEMT low noise distributed amplifier covering direct current to 20 GHz, with 14 dB of gain, 2.5 dB of noise figure and 16 dBm at one decibel compression at 10 GHz, drawing 60 mA from an 8 V supply with the gate adjusted between minus 2 V and 0 V. As die it measures 3.12 mm by 1.63 mm by 0.1 mm, and the LC5 order code supplies the same amplifier in a ceramic surface mount package. The noise figure per milliamp is the reason the part is still specified into new builds at 10 GHz: 0.48 W of DC for a 2.5 dB front end is a difficult combination to match.

Published values

ParameterValue
Frequency rangeDC to 20 GHz
Gain at 10 GHz14 dB
Noise figure at 10 GHz2.5 dB
Output power at 1 dB compression at 10 GHz16 dBm
Supply8 V at 60 mA
Gate adjustmentminus 2 V to 0 V, minus 0.9 V typical for 60 mA
Die size3.12 mm by 1.63 mm by 0.1 mm
Matching50 ohm input and output on chip
Reference measurement0.025 mm bonds of 0.31 mm minimum length in a 50 ohm fixture

Half a watt of DC for a 2.5 dB front end

8 V at 60 mA is 0.48 W. At the 16 dBm compression point the output is 40 mW, so 0.44 W is dissipated, and the die face is 5.1 square millimetres. That is 0.086 W per square millimetre, which is low enough that the package or the carrier is decided by the radio frequency transition rather than by heat.

The reason to care about the current is battery life and the reason to care about the noise figure is sensitivity, and this part sits at an unusual point on that trade: 60 mA is low enough for a portable receiver, and 2.5 dB at 10 GHz is good enough that the front end loss dominates the system figure. Every decibel of loss between the antenna and this amplifier is a decibel of system noise figure, which makes the connector and the filter ahead of it worth more attention than the amplifier itself.

A gate that has to be set, on a part with 14 dB of gain

The gate is adjusted between minus 2 V and 0 V to reach 60 mA, with minus 0.9 V typical. Because the part has 14 dB of gain the bias network is inside the loop, and any noise on the gate rail is amplified along with the signal. That is why the gate decoupling capacitor is placed at the pin and returned to the same ground the source pins use, and why a gate rail shared with a switching regulator is a bad idea even when the average voltage is right.

The drain current also sets the gain and the compression point, so a lot that draws 50 mA instead of 60 mA will read perhaps a decibel lower in gain and a decibel lower in compression. That is within the spread the adjustment range exists for, and the bias loop or the trim on each board is what brings it back.

Direct current to 20 GHz, which is a wider claim than it looks

The amplifier is specified from direct current, which matters for a baseband or intermediate frequency path that has to start at a few megahertz, and it holds to 20 GHz with the gain falling from 14 dB towards 13 dB at the top of the range and the noise figure rising from 2.5 dB to about 4 dB. A receiver that uses it across the whole span has to size the cascade on the top of the band.

For a second source study the three figures to compare are the noise figure at 10 GHz, the gain at 10 GHz and the current at 8 V. A replacement that is quieter but draws three times the current is a different part for a portable product, and a replacement that matches the noise figure but rolls off above 12 GHz loses the top of the band that the original covered.

For a board that has to keep running while a reel runs out, the LNA selection guide is where the family alternatives sit, the RF component sourcing page is the check list before a substitute goes in, and how to verify a drop in replacement is how a gap is covered without a new line item.

Two questions buyers ask

Does the HMC460 need a negative rail? It needs a gate voltage between minus 2 V and 0 V relative to the source to set 60 mA, which in practice means either a negative rail or a source resistor that lifts the source above ground. The typical value for 60 mA is minus 0.9 V.

Why does the noise figure rise at the top of the band? The published figure of 2.5 dB is at 10 GHz. Above 18 GHz the gain falls and the noise figure rises to about 4 dB, so a system that uses the whole 20 GHz span has to size the cascade at the top of the band.