Contact Us

HMC1144-Die

Brand: Analog Devices
Analog Devices HMC1144-Die is a analog & mixed-signal component designed for Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

HMC1144-Die — Analog & Mixed-Signal ICs | Superb Automation

HMC1144-Die

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The HMC1144-Die from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

HMC1144 die: 19 dB and 22 dBm from 35 GHz to 70 GHz

The HMC1144 is a gallium arsenide pHEMT medium power amplifier die covering 35 GHz to 70 GHz with 19 dB of gain, 21 dBm at one decibel compression in the upper part of the band, 22 dBm saturated, 28 to 32 dBm of output third order intercept and 33 to 35 dB of input return loss in the lower bands, from 4 V at 320 mA. The die is 2.3 mm by 1.8 mm by 0.05 mm and its four drain pads and two gate pads are separate, which makes per stage current measurement possible on an assembly that is otherwise not reworkable.

Published values

ParameterValue
Frequency range35 GHz to 70 GHz, three specified bands
Gain19 dB typical, 17 dB minimum in the 40 to 50 GHz band, 19 dB from 50 to 70 GHz
Gain variation over temperature0.016 to 0.023 dB per degree
Input return loss33 dB, 35 dB and 22 dB across the three bands
Output return loss16 dB, 16 dB and 25 dB
Output power at 1 dB compression19 dBm at 35 to 40 GHz, 19.5 dBm at 40 to 50 GHz, 21 dBm at 50 to 70 GHz
Saturated output power21 dBm, 21.5 dBm and 22 dBm
Output third order intercept28 dBm, 28 dBm and 32 dBm at 10 dBm per tone
Supply4 V on four drains, 320 mA total, 1.28 W of DC
Gate biasVGG1A and VGG1B adjustable minus 2 V to 0 V
Die size2.3 mm by 1.8 mm by 0.05 mm

Thirty three decibels of input match is rare at these frequencies

A 33 dB input return loss is a voltage standing wave ratio of about 1.05 to 1, which is very close to a perfect 50 ohm. At 35 GHz that is a genuine achievement and it means the input bond and the preceding stage have very little influence on the gain response, which is the opposite of the situation on most E-band die where a few tenths of a millimetre of bond wire move the match.

The top band gives some of that back, with 22 dB at 50 GHz to 70 GHz, but even there the match is better than most parts in this class. For a module the practical benefit is that the input side needs less tuning and can be bonded with a standard ribbon length, so the assembly drawing is less sensitive to the bonder operator. That is worth as much as a decibel in a production environment.

One point one two watts in four square millimetres, and four drain pads

4 V at 320 mA is 1.28 W of DC. At the 22 dBm saturated point the output is 158 mW, so 1.12 W becomes heat on 4.14 square millimetres, which is 0.27 W per square millimetre. Four separate drain pads are the vendor's way of distributing that current, and they exist because the on chip drain line cannot carry 320 mA in one place without electromigration and voltage drop.

For the assembly the four pads mean four bias feeds and a decision about how to combine them. Tying all four to one bond pad on the board is electrically the same and thermally worse, because the current still has to flow through one pad and one bond. Bringing each drain out on its own pad and combining them on a low frequency network is the better route, and it also gives four current measurement points that separate a stage fault from a bias fault.

Twenty eight to thirty two decibels of intercept for a multicarrier link

The intercept is specified at 10 dBm per tone, and in the top band it is 32 dBm while the compression point is 21 dBm. That is 11 dB of margin, which is what a multicarrier E-band link needs: two carriers at 5 dBm each are 27 dB below the intercept, so the third order products are 54 dB down, and a link carrying four carriers still has usable spurious free range.

In the lower bands the intercept is 28 dBm against a compression point of 19 dBm, so the margin is 9 dB and the same four carriers give about 46 dB. That is the band where a system with a tight spectral mask has to check, and it is also where the input match is best, so the part is at its most predictable exactly where the linearity is lowest.

Buyers usually arrive at the RF component sourcing page to find the family alternatives, then use the RF power transistor cross reference to confirm a substitute before it is fitted; one stop RF supply is the routine for a part that has already stopped shipping.

Two questions buyers ask

Are the four drain pads independent? They are separate pads for current distribution. Each can be fed and measured separately, and tying them together on the board is electrically the same but thermally worse.

Is 22 dBm available from 35 GHz? No. The 22 dBm saturated figure belongs to the 50 GHz to 70 GHz band. At 35 GHz to 40 GHz the compression point is 19 dBm.