HMC1127
Product Specifications
HMC1127
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The HMC1127 from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
HMC1127: 15 dB of gain to 50 GHz and 80 mA of drain current
The HMC1127 is a gallium arsenide pHEMT distributed power amplifier die covering 2 GHz to 50 GHz with 15 dB of gain in the low band, 14.5 dB from 30 GHz up, 14 dBm at one decibel compression, 18.5 dBm saturated and 25.5 dBm of output third order intercept, from 80 mA at 5 V. The die is 2.7 mm by 1.45 mm by 0.1 mm. It is the higher gain, higher current sibling of the 65 mA amplifier that covers the same range, and the choice between them is a gain budget against a dissipation budget.
Published values
| Parameter | Value |
|---|---|
| Frequency range | 2 GHz to 50 GHz, four specified bands |
| Gain | 15 dB typical 2 to 8 GHz, 13.5 dB 8 to 30 GHz, 14.5 dB 30 to 50 GHz |
| Gain variation over temperature | 0.005 to 0.012 dB per degree |
| Noise figure | 8.0 dB, 6.5 dB, 6.0 dB and 5.0 dB across the four bands |
| Input return loss | 17 dB, 18 dB, 20 dB and 13 dB |
| Output return loss | 10 dB, 20 dB, 17 dB and 13 dB |
| Output power at 1 dB compression | 14 dBm, 12.5 dBm, 12 dBm and 10.5 dBm |
| Saturated output power | 18.5 dBm, 17.5 dBm, 17 dBm and 15 dBm |
| Output third order intercept | 25.5 dBm, 23 dBm, 22 dBm and above |
| Supply | 80 mA at 5 V, 0.4 W of DC |
| Gate bias | VGG2 at 1.4 V, VGG1 adjusted for 80 mA |
| Die size | 2.7 mm by 1.45 mm by 0.1 mm |
Eight decibels of noise figure and why the part still sells
A first stage with 8 dB of noise figure is not a low noise amplifier by any normal definition, and the vendor does not claim it is. What the part offers is 15 dB of gain at 2 GHz and 14.5 dB at 40 GHz from a single stage, which is what a transmit chain or an intermediate frequency block needs. In a receive chain it belongs after the low noise stage, where its 8 dB figure is divided by the gain ahead of it and contributes almost nothing.
The comparison with the 65 mA part in the same family is instructive: that one gives 11 dB of gain with 4.5 dB of noise figure, this one gives 15 dB with 8 dB. Both are correct answers to different questions, and a specification that asks for gain and noise figure without saying which stage of the chain is being bought will get whichever part the supplier has in stock.
Point four watts and the top band where compression falls to 10.5 dBm
5 V at 80 mA is 0.4 W of DC. At 18.5 dBm saturated the low band output is 71 mW, so 0.33 W becomes heat; at the top band, 15 dBm saturated is 32 mW and the heat is 0.37 W. The dissipation is therefore nearly constant and slightly higher at the top of the band, where the output is lowest, which is the opposite of what a driver budget usually assumes.
That matters for a system that operates near 50 GHz: the amplifier is hottest when it is delivering the least power, because the current is fixed. A thermal sensor placed near the part will read high in a receive mode where the transmit chain is idling, and an operator who interprets that reading as a fault will be chasing a part that is behaving exactly as specified.
Four bands of return loss and the one that matters
The output return loss is 10 dB in the low band and 20 dB in the 8 GHz to 30 GHz band, which is a large difference for the same amplifier. It reflects the way the output line is terminated, and it means that a system operating at 3 GHz sees a 2 to 1 mismatch while one at 20 GHz sees almost none. The low band is also where the gain is highest and the compression point best, so the mismatch is at the frequency where the part has the most margin.
For a wideband instrument the practical consequence is that a level detector placed after the amplifier reads differently at 3 GHz and at 20 GHz for the same drive, and the calibration has to be per band rather than per instrument. That is a firmware question rather than a hardware one, and it is cheaper to discover before the calibration routine is frozen.
Where a customer needs a second position on this part, the RF component sourcing page is the starting point, how to choose an RF amplifier sets out the checks a substitution has to pass, and one stop RF supply is the short lead time route we quote against.
Two questions buyers ask
Is the HMC1127 a low noise amplifier? No. The noise figure is 6 dB to 8 dB. It is a gain block for a transmit or intermediate frequency chain, where 15 dB of gain to 50 GHz is what it is bought for.
Can it run at 8 V like the smaller part in the family? The specified operating point is 5 V at 80 mA. The supply is a current sink, so the drain voltage is a thermal choice, and 0.4 W is already what the die has to carry.