Contact Us

ADG1606BRUZ-REEL7

Brand: Analog Devices
Analog Devices ADG1606BRUZ-REEL7 is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

ADG1606BRUZ-REEL7 — Analog & Mixed-Signal ICs | Superb Automation

ADG1606BRUZ-REEL7

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The ADG1606BRUZ-REEL7 from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

ADG1606BRUZ-REEL7: A 16 to 1 Multiplexer with 4.5 ohm Switches and 378 mA per Channel

What this part is

The ADG1606 is a monolithic multiplexer that connects one of sixteen inputs to a common output under four binary address lines, with an enable input that turns every channel off. The switch element is built on the iCMOS process, which is what allows a part with 3 V logic inputs to sit on a plus and minus 8 V analogue supply without a separate logic rail. On resistance is 4.5 ohm typical with 1.1 ohm of flatness across the signal range, and the channel conducts equally well in both directions, so the same part works as a 1 to 16 demultiplexer.

The family covers the differential case as well: the ADG1607 switches one of eight differential inputs to a common differential output. The ADG1606 is the single ended member, offered in a 28 lead TSSOP and a 32 lead LFCSP of 5 mm by 5 mm. Applications run from data acquisition and gain switching to audio and video routing, relay replacement and automatic test equipment, and the common thread is a signal path that needs low distortion rather than a signal path that needs isolation.

Published figures that matter to a buyer

Configuration16 to 1, single ended
Address lines4, plus an enable input
On resistance4.5 ohm typical
On resistance flatness1.1 ohm
On resistance over temperature7.5 ohm maximum
Dual supplyplus and minus 3.3 V to plus and minus 8 V
Single supply3.3 V to 16 V
Logic levels3 V compatible, 2.0 V high, 0.8 V low
Continuous currentup to 378 mA per channel
DistortionTHD plus N of 0.04 percent
Body28 lead TSSOP or 32 lead LFCSP of 5 mm by 5 mm
Logic supplynone required

Where the headline numbers stop

Four and a half ohms is a room temperature typical, and the maximum over temperature is 7.5 ohm, which is a 67 percent increase. That difference decides the current rating in practice: 378 mA through 4.5 ohm drops 1.70 V and dissipates 0.643 W in the switch, while the same current through 7.5 ohm drops 2.83 V and dissipates 1.07 W. A channel carrying a third of an amp is a power component, and the 28 lead TSSOP has to be treated as such. In a signal path the same resistance shows up differently: 1.1 ohm of flatness into a 10 kohm load is 0.011 percent of gain error, which is below the distortion the part itself contributes, while the same flatness into a 1 kohm load is 0.11 percent and becomes visible.

A THD plus N figure of 0.04 percent is minus 68 dB, or about 11 effective bits. That is fine for a multiplexed 12 bit acquisition channel and marginal for a 16 bit one, where the switch, not the converter, would set the floor. The part is a routing element, not a precision attenuator: nothing in the data sheet promises channel to channel gain matching, so a system that calibrates each channel separately carries sixteen sets of coefficients.

The 16 V single supply ceiling also means the part cannot sit directly on a plus and minus 15 V signal path; at plus and minus 8 V dual, a 16 V peak to peak signal is the limit and any margin for a transient has to come from the supplies, not from the switch.

Applications where it fits

  • Data acquisition systems that scan sixteen sensor channels into one converter.
  • Programmable gain stages and resistor network switching in instrumentation.
  • Automatic test equipment that routes a single instrument to many device pins.
  • Audio and video signal routing where a mechanical relay is being replaced.
  • Sample and hold front ends and battery powered multipoint monitors.

Two questions buyers ask

Does the enable pin disconnect the signal or just the address decoder? It disables the device so that all channels switch off, which means the common output floats rather than holding the last channel. A system that needs the previous channel to remain connected through a scan has to keep the enable asserted and change only the address.

Is the differential part a different die? The ADG1607 is the eight channel differential member of the same family, with three address lines instead of four and the same switch element. It shares the package options, so the two are interchangeable only at the board level with a different part fitted, not by changing an address.

Sourcing notes and next step

ADG1606BRUZ-REEL7 is the 28 lead TSSOP in tape and reel; the LFCSP body carries a different order code and a different footprint, so the two cannot be mixed on one assembly without a stencil change. The part is in production, and the order code is stable enough that a shortage is usually a date code question rather than an end of life question. The analog and mixed signal IC family page lists the switch and multiplexer line, the pin to pin cross reference page sets out what a substitute has to match beyond the pinout, and the BOM shortage recovery page covers the route when the reel is not on the shelf.

Request Quote — In Stock, 100% New & Original, Full Warranty