AD5314ARMZ-REEL7
Product Specifications
AD5314ARMZ-REEL7
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The AD5314ARMZ-REEL7 from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
AD5314ARMZ-REEL7: Four 10 Bit Outputs from One Reference Pin and Half a Milliamp
What this part is
The AD5314 holds four 10 bit voltage output converters with buffered outputs in a 10 lead body, running from a single 2.5 V to 5.5 V supply. All four converters take their reference from one pin, the outputs update together on a load command, and the outputs power up at 0 V and stay there until a valid word is written. A power-down mode takes the part to 80 nanoamps at 3 V, which is what makes it usable in equipment that spends most of its life asleep.
The output amplifier swings rail to rail with a 0.7 volt per microsecond slew rate, the serial port is three wire and runs at clock rates up to 30 MHz, and the part is monotonic over all codes by specification rather than by test limit. The body is a 10 lead MSOP or a 10 lead leadless frame chip scale package, and the temperature range is minus 40 to plus 105 degrees C. The A and W versions are specified at plus or minus 4 LSB of integral non linearity and the B version at plus or minus 2.5 LSB.
Published figures that matter to a buyer
| Resolution | 10 bit, four converters |
| Supply | 2.5 V to 5.5 V |
| Reference | one pin shared by all four converters |
| Output range | 0 V to the reference voltage |
| Integral non linearity | plus or minus 4 LSB, A and W versions; 2.5 LSB, B version |
| Monotonicity | guaranteed over all codes |
| Supply current | 500 microamps at 3 V, 600 microamps at 5 V |
| Power down | 80 nanoamps at 3 V, 200 nanoamps at 5 V |
| Output amplifier | rail to rail, 0.7 volts per microsecond |
| Serial port | three wire, up to 30 MHz |
| Power on state | outputs at 0 V until written |
| Body | 10 lead MSOP or 10 lead leadless frame chip scale |
Where the headline numbers stop
Four LSB on a 10 bit converter is 0.39 percent of full scale, which is a quarter of a percent of a 10 V span if the reference is 10 V, and 9.8 mV on a 2.5 V reference. One count is 2.44 mV on a 2.5 V reference, so a setpoint written as a code has a granularity of 2.44 mV and a linearity of about four of those counts: the linearity, not the resolution, is the accuracy of the channel.
The single reference pin is a shared resource. A reference with 1 percent initial error and 50 ppm per degree C of drift puts the same error on all four channels, which is fine when the four channels are a related group and wrong when one of them is a calibrated output and another is a bias. The drift of the reference is also not removable by calibration at one temperature, so the reference specification belongs in the channel budget next to the converter linearity.
Power is genuinely low: 500 microamps at 3 V is 1.5 mW for four channels, and the 80 nanoamp power-down state is 0.24 microwatts. The cost of that is a 10 bit converter and a 0.7 volt per microsecond output stage, so the part is for setting bias levels and offsets rather than for generating a waveform. A 16 bit word on a 30 MHz clock takes 533 nanoseconds, so the interface is never the limit at these update rates.
Applications where it fits
- Digital gain and offset adjustment in instrument channels.
- Programmable voltage and current sources at low resolution.
- Programmable attenuators and bias networks.
- Portable battery instruments with four setpoints and a long sleep cycle.
- Industrial process control where a 10 bit setpoint is enough and the board space is not.
Two questions buyers ask
Is the AD5324 a direct substitute? The AD5304, AD5314 and AD5324 are the 8, 10 and 12 bit members of the same family in the same package with the same pin arrangement and the same port, so the upgrade path is real and the order code is the only thing that changes. The price difference is the reason to ask whether 10 bits is enough before a board is released rather than after.
What happens to the outputs during a brownout? The part powers up with the outputs at 0 V and holds them there until a valid write, which is the behaviour a bias network wants: no output until the host has decided what the output should be. An application that needs the previous setting restored after a supply glitch has to write it again, because the register content is not retained without a supply.
Sourcing notes and next step
AD5314ARMZ-REEL7 is the A grade in the 10 lead MSOP body on tape and reel. The grade letter before the body code changes the linearity limit, so a B grade request filled with an A grade is a different specification even though the part works in the socket. The ADC and DAC cross reference page sets out the comparison fields, the component cost page covers the levers on a commodity converter, and the analog and mixed signal IC family page lists the rest of the converter line.
Request Quote — In Stock, 100% New & Original, Full Warranty