Contact Us

HMC-AUH312-Die

Brand: Analog Devices
Analog Devices HMC-AUH312-Die is a analog & mixed-signal component designed for Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

HMC-AUH312-Die — Analog & Mixed-Signal ICs | Superb Automation

HMC-AUH312-Die

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The HMC-AUH312-Die from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

HMC-AUH312 die: 0.5 GHz to 80 GHz from 1.2 square millimetres

The HMC-AUH312 is a gallium arsenide HEMT distributed low noise amplifier die covering 0.5 GHz to 80 GHz with 10 dB of small signal gain to 60 GHz and 9 dB above it, 5 dB of noise figure, 13.5 dBm at one decibel compression and 23 dBm of output third order intercept, from 8 V at 60 mA. The die is 1.2 mm by 1.0 mm by 0.1 mm, which is 1.2 square millimetres, and the input and output pads double as bias ports, so the amplifier can be biased through bias tees on the radio frequency lines or directly on the pads.

Published values

ParameterValue
Frequency range0.5 GHz to 80 GHz, specified in two bands
Gain8 dB minimum, 10 dB typical to 60 GHz; 9 dB typical 60 to 80 GHz
Noise figure5 dB typical
Input return loss15 dB to 60 GHz, 10 dB above
Output return loss17 dB to 60 GHz, 15 dB above
Output power at 1 dB compression13.5 dBm to 60 GHz, 13 dBm above
Saturated output power16 dBm and 15 dBm
Output third order intercept23 dBm and 22 dBm
Supply without bias tee6 V or 8 V, 60 mA, 360 mW or 480 mW of DC
Supply with bias tee5 V, 60 to 80 mA, 300 mW of dissipation
Gate biasVGG1 minus 2 V to 0 V to set 60 mA, VGG2 at 1.8 V
RF input power4 dBm maximum
Die size1.2 mm by 1.0 mm by 0.1 mm

Two pads that are both a radio frequency port and a bias point

RFIN is also VGG1 and RFOUT is also VDD, which is why the part can be used with or without bias tees. Without a bias tee the bias is applied directly to the pads through the board, and the pad then has to sit at dc while carrying 0.5 GHz to 80 GHz, so the bias network has to be a choke that looks like an open circuit across ten octaves. With a bias tee the pads are dc blocked and the bias comes in on a separate arm, which is easier to get right and adds the insertion loss of the tee.

The document gives two different DC points for the two configurations: 300 mW of dissipation with a bias tee at 5 V, and 360 mW at 6 V or 480 mW at 8 V without one. The higher voltage without a tee is not a different amplifier, it is the same current pushed through a longer bias path, and the thermal answer follows the dissipation rather than the voltage. A user who reads 8 V and 480 mW and then adds a bias tee will be running the part harder than the reference configuration for no gain.

Point four eight watts on 1.2 square millimetres

At 8 V and 60 mA the dissipation is very nearly the whole DC input, because the output at the compression point is 22 mW. That is 0.48 W on a die face of 1.2 square millimetres, which is 0.4 W per square millimetre, the highest flux of any part in this batch and eight times the figure for the 22 GHz die. A 0.1 mm substrate spreads a little, and not enough to matter.

The consequence is that the attach is the limiting element, not the amplifier. A 20 degrees per watt path from die to carrier is a 9.6 degree rise, and a 100 degrees per watt epoxy layer under the whole die would contribute 48 degrees, which is the difference between a part that runs at 60 degrees and one that runs at 105. For a die this small with this flux, a eutectic or sintered attach is not a refinement.

Five decibels of noise figure across ten octaves is the honest trade

A distributed amplifier that covers 0.5 GHz to 80 GHz cannot also be a 1 dB noise figure part, because the input matching network is a transmission line rather than a tuned circuit and the loss of that line appears directly in the noise figure. Five decibels is what the topology gives, and the applications list in the document reflects it: photoreceiver post amplifiers, modulator drivers, test equipment and radar warning receivers, all of which have a stage ahead of this one or a signal large enough not to care.

Where the part earns its place is bandwidth per square millimetre. A 1.2 square millimetre die that covers 160 to 1 in frequency replaces a switched bank of four or five narrowband amplifiers, and the switch loss that the bank would have added is usually more than the difference in noise figure. That is the argument to make when a specification asks for a lower noise figure across the same range: the alternative is not a better single part, it is a different architecture.

Buyers usually arrive at the RF component sourcing page to find the family alternatives, then use the LNA selection guide to confirm a substitute before it is fitted; one stop RF supply is the routine for a part that has already stopped shipping.

Two questions buyers ask

Can the amplifier be biased without bias tees? Yes. The input and output pads double as the gate and drain connections, so 6 V or 8 V can be applied directly through a choke on the board, at 360 mW or 480 mW of dissipation.

Is 5 dB of noise figure usable at the front end? Only where the signal is large or where a lower noise stage precedes it. For a sensitive receiver the part is a post amplifier, not a first stage.