Contact Us

ADPA7007AEHZ

Brand: Analog Devices
Analog Devices ADPA7007AEHZ is a analog & mixed-signal component designed for Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

ADPA7007AEHZ — Analog & Mixed-Signal ICs | Superb Automation

ADPA7007AEHZ

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The ADPA7007AEHZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

ADPA7007AEHZ: the same die in a 7 mm carrier, specified in three band slices

The ADPA7007AEHZ is the packaged form of the 18 GHz to 44 GHz amplifier, in an 18-terminal, 7 mm by 7 mm ceramic leadless chip carrier with a heat sink. It delivers 31.5 dBm of saturated output and 29 dBm at one decibel compression between 26 GHz and 34 GHz, 20.5 dB of gain between 34 GHz and 44 GHz and up to 42.5 dBm of output third order intercept, from 5 V at 1400 mA. The data sheet divides the band into three slices, 20 GHz to 26 GHz, 26 GHz to 34 GHz and 34 GHz to 44 GHz, and each slice reads differently.

Published values

ParameterValue
Frequency range18 GHz to 44 GHz, specified in three slices
Saturated output power31.5 dBm typical, 26 GHz to 34 GHz
Output power at one decibel compression29 dBm typical, 34 GHz to 44 GHz
Gain20.5 dB typical, 34 GHz to 44 GHz
Output third order interceptup to 42.5 dBm typical
Supply5 V at 1400 mA
Package18-terminal, 7 mm by 7 mm LCC_HS
Extrasintegrated power detector, 50 ohm matched input and output
Typical gate voltageminus 0.685 V for 1400 mA
Dissipation at saturation5.59 W

Why the package quotes less than the die

The die version of this amplifier quotes 32 dBm and 31 dBm at compression between 22 GHz and 36 GHz. The packaged version quotes 31.5 dBm of saturation in 26 GHz to 34 GHz and 29 dBm at one decibel compression in 34 GHz to 44 GHz. Part of that is the package transition loss at the top of the band, and part is a different specification slice; the two documents are not measuring the same window.

For a buyer comparing the two, the honest comparison is at the frequency of use. At 30 GHz both are about 31 dBm. At 42 GHz the package is 29 dBm at compression while the die document has no number in that slice at all, so the packaged part is the one with a published figure where it matters.

Three slices means three sets of expectations

A specification written from the 26 GHz to 34 GHz table will be optimistic at 44 GHz, where gain is 20.5 dB rather than the higher figure in the middle of the band. Wideband equipment is usually specified per band, and the amplifier data sheet is arranged the same way for the same reason.

The 42.5 dBm intercept is an upper figure across the family of slices rather than a constant. Linearity in a multi carrier system has to be taken from the slice the carriers occupy, and a system that puts two carriers 10 GHz apart crosses the slices and gets neither number.

Heat, bias and the detector on a packaged part

5 V at 1.4 A is 7.0 W against 1.41 W of saturated output, so 5.59 W is dissipated into a 7 mm carrier. The heat sink pad handles it given a via field and copper, and the gate is set for 1400 mA with a typical of minus 0.685 V. Because the drain current rises with temperature at a fixed gate voltage, the bias arrangement has to be a current loop rather than a divider if the case temperature moves by tens of degrees.

The detector is temperature compensated and follows the envelope, which suits a level loop that samples inside a pulse. Its slope varies across 26 GHz of bandwidth, so a calibrated power reading needs a per slice correction, and an uncalibrated health indication does not.

Where a customer needs a second position on this part, the pin to pin cross reference is the starting point, the RF power transistor cross reference sets out the checks a substitution has to pass, and how to verify a drop in replacement is the short lead time route we quote against.

Two questions buyers ask

Which slice should a 40 GHz system be specified from? The 34 GHz to 44 GHz slice, where the package quotes 29 dBm at one decibel compression and 20.5 dB of gain.

Is this a drop in replacement for the die version? No. It is the same amplifier in a package, so the pin out, the thermal path and the board footprint all differ. It is an alternative route to the same performance, not a substitution.