Contact Us

ADPA7007-Die

Brand: Analog Devices
Analog Devices ADPA7007-Die is a analog & mixed-signal component designed for Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

ADPA7007-Die — Analog & Mixed-Signal ICs | Superb Automation

ADPA7007-Die

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The ADPA7007-Die from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

ADPA7007 die: 32 dBm and 21.5 dB of gain from 18 GHz to 44 GHz on one chip

The ADPA7007 in die form is a gallium arsenide pHEMT amplifier covering 18 GHz to 44 GHz with 32 dBm of saturated output power, 31 dBm at one decibel compression and 21.5 dB of gain between 22 GHz and 36 GHz, plus 41 dBm of output third order intercept between 22 GHz and 44 GHz, from 5 V at 1400 mA. The die is 3.610 mm by 3.610 mm by 0.102 mm with 50 ohm input and output on chip. Twenty six gigahertz of bandwidth at the one watt level from a single die is why this part appears in wideband front ends, and the 5.42 W of heat it produces is why those front ends need a carrier.

Published values

ParameterValue
Frequency range18 GHz to 44 GHz, specified in slices
Saturated output power32 dBm typical, 22 GHz to 36 GHz
Output power at one decibel compression31 dBm typical, 22 GHz to 36 GHz
Gain21.5 dB typical, 22 GHz to 36 GHz
Output third order intercept41 dBm typical, 22 GHz to 44 GHz
Supply5 V at 1400 mA maximum
Die size3.610 mm by 3.610 mm by 0.102 mm
Matching50 ohm input and output
Dissipation at saturation5.42 W
Typical gate voltageminus 0.685 V for 1400 mA

Five point four watts over thirteen square millimetres

1.4 A at 5 V is 7.0 W of DC input. Saturated output is 1.58 W, so 5.42 W leaves as heat through a die face of 13.03 square millimetres, which is 0.42 W per square millimetre. That is lower density than the smaller 29 dBm die in the family, because the area grew faster than the power, and it is the reason this part is the more forgiving of the two to mount.

Forgiving is not the same as trivial. At 5.42 W a 25 degree case needs the attach and the carrier to hold the channel below the maximum, and the data sheet thermal figures are for the die bottom rather than the channel, so the difference has to be carried in the margin. A carrier with a good expansion match and a void free attach under the output section is the working answer.

Wideband means the gain slope is real

21.5 dB is quoted between 22 GHz and 36 GHz, and 32 dBm of saturation belongs to the same slice. The part covers 18 GHz to 44 GHz, so there are specification slices above and below where the numbers differ. A system that sweeps the whole 26 GHz span and expects flat output is asking for something the data sheet does not promise.

At the bottom of the band the gain is higher and the output is lower; at the top the gain falls away. If the chain has a level control loop with a few decibels of range, this is absorbed. If it does not, the sweep shows a tilt that gets blamed on the antenna or the cable, and the actual cause is the amplifier's own slope.

Bias, detector and the packaging decision

The gate is adjusted to reach 1400 mA, with a typical of minus 0.685 V. On a die the bias network is on the carrier, so the gate decoupling capacitor and the drain bypass are as close to the pads as the assembly allows. The on chip detector is temperature compensated and its output is a pad, which means the sampling circuit is on the carrier too and the trace length matters at 44 GHz.

The packaged equivalent of this amplifier is a 7 mm leadless carrier with a heat sink, which trades about a decibel and a half of output at the top of the band for a tested interface and a quoted thermal resistance. Wideband instruments usually take the die, and equipment built in the hundreds takes the package.

Buyers usually arrive at the RF component sourcing page to find the family alternatives, then use the RF power transistor cross reference to confirm a substitute before it is fitted; how to choose an RF amplifier is the routine for a part that has already stopped shipping.

Two questions buyers ask

Is the 32 dBm figure valid up to 44 GHz? The 32 dBm and 31 dBm figures are specified from 22 GHz to 36 GHz. The data sheet splits the range into slices and the upper slice carries lower output power.

What carrier should the die be mounted on? One with a thermal expansion close to gallium arsenide and a void free attach under the output section. At 5.42 W the attach quality sets the channel temperature more than the carrier material does.