LT3060ETS8#TRPBF
Product Specifications
LT3060ETS8#TRPBF
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The LT3060ETS8#TRPBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
LT3060ETS8#TRPBF: Forty Microamps of Quiescent Current Is the Whole Point, and It Sets the Rest
The LT3060 is a 100 mA low dropout regulator that runs from 1.6 V to 45 V with 40 uA of quiescent current, 30 uV rms of noise, 300 mV of dropout at full load and a shutdown current below 1 uA, in an 8-lead TSOT-23 or a 2 mm by 2 mm DFN. The ETS8 code here is the TSOT-23 body. The quiescent current is the reason the part exists and it also explains the rest of the data sheet: 40 uA over a year on standby is 0.35 Ah, which is the difference between a battery product that survives a shelf life and one that does not, but 40 uA at 45 V is also 1.8 mW dissipated with no load at all.
Input voltage times output current is the thermal budget
45 V to 3.3 V at 100 mA is 4.17 W, and the TSOT-23 body has no exposed pad, so the junction rise is set entirely by the copper the three leads sit on. 12 V to 3.3 V at 100 mA is 0.87 W, which the package can hold with a reasonable pour. The practical rule for this family is that the current rating is available at input voltages where the dissipation stays under about half a watt, and above that the load has to come down or the drop has to be split. The 1.6 V minimum input and the 45 V maximum cover a very wide span, and the two ends are used for completely different circuits: a single cell rail at one end and a 24 V or 48 V industrial backplane at the other.
| Input to output | Dissipation at 100 mA | Dissipation at 20 mA |
|---|---|---|
| 45 V to 3.3 V | 4.17 W | 0.83 W |
| 24 V to 3.3 V | 2.07 W | 0.41 W |
| 12 V to 3.3 V | 0.87 W | 0.17 W |
| 5 V to 3.3 V | 0.17 W | 0.03 W |
The reference capacitor does three jobs
One external capacitor on the REF/BYP pin filters the reference, sets the output noise and sets the soft start ramp. The 30 uV rms noise figure is a with capacitor figure, and the minimum output capacitance is 2.2 uF of ceramic with a low ESR, which is a stability requirement rather than a ripple one. Because the part is stable with ceramic output capacitors, the usual ESR resistor that older low dropout regulators needed can be removed, and that resistor was often the largest tolerance in the loop.
Fixed and adjustable versions are not the same board
The family covers 1.2 V, 1.5 V, 1.8 V, 2.5 V, 3.3 V, 5 V and 15 V fixed outputs plus an adjustable version with a 600 mV reference that reaches 44.5 V. The fixed versions divide the feedback internally and the adjustable one does not, so the same footprint takes a different resistor pair and a different noise gain. That difference is why a board that was qualified with a fixed 3.3 V part cannot take an adjustable part at the same setting without a recheck of the transient response, even though the pins line up. Reverse battery protection, reverse output protection and foldback current limit are all internal, which matters on a 45 V input where a wiring error is a real possibility.
The long life industrial rail
This part is qualified to AEC-Q100 and specified over the automotive temperature range, so it is usually chosen for a rail that has to sit across a 24 V backplane for a decade rather than for a fast transient. The power management cross reference page covers the family, the component obsolescence management page covers the long life question, and incoming checks follow the incoming inspection plan.