Contact Us

ADP1763ACPZ

Brand: Analog Devices
Analog Devices ADP1763ACPZ is a analog & mixed-signal component designed for Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

ADP1763ACPZ — Analog & Mixed-Signal ICs | Superb Automation

ADP1763ACPZ

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The ADP1763ACPZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

ADP1763ACPZ: 3 A from a 1.10 V input, with 2 uV rms of noise

The ADP1763ACPZ is a 3 A CMOS low dropout regulator built for rails that have almost no headroom: the input window is 1.10 V to 1.98 V with no external bias supply, and the adjustable output runs from 0.5 V to 1.5 V. It is the part that sits between a 1.2 V or 1.8 V intermediate bus and a core rail on a data converter or a high speed transceiver, where the noise floor and the dropout both have to be small at the same time.

Published values

ParameterValue
Maximum output current3 A
Input voltage range1.10 V to 1.98 V, no external bias
Adjustable output range0.5 V to 1.5 V
Fixed output range0.9 V to 1.5 V
Output noise, 100 Hz to 100 kHz2 uV rms
Noise density4 nV per root Hz at 10 kHz, 3 nV per root Hz at 100 kHz
Dropout at 3 A95 mV typical
PSRR at 3 A59 dB at 10 kHz, 43 dB at 100 kHz
Supply current, no load4.5 mA typical
Accuracy over line, load, temperature1.5%
Output capacitor10 uF ceramic
ExtrasProgrammable soft start, current limit, thermal protection

Why a low input window is a feature

A regulator that accepts 1.10 V to 1.98 V cannot be used on a 3.3 V bus, and that is deliberate. The part is aimed at a board where a switching stage has already produced 1.2 V or 1.8 V and the remaining job is to remove several millivolts of ripple without losing 95 mV of headroom at 3 A. Using a wider input LDO in the same socket wastes efficiency and puts more heat into a small package.

The 95 mV dropout at 3 A is the number that decides whether the topology works. A 1.2 V bus feeding a 1.0 V core rail leaves 200 mV, which is comfortable. The same bus feeding a 0.9 V rail leaves 300 mV and is still fine, but the intermediate bus tolerance has to be added on top, because a 5 percent low bus removes 60 mV of that margin before the regulator sees it.

Noise density against integrated noise

The 2 uV rms figure is integrated from 100 Hz to 100 kHz, and the density figures of 4 nV and 3 nV per root hertz at 10 kHz and 100 kHz are what a converter datasheet can be compared against. For an ADC reference or a clock supply the density at the specific offset matters more than the integrated number, so both are quoted here for the comparison table.

Soft start, current limit and the 10 uF output

At 3 A the inrush into a 10 uF output capacitor is large enough to trip a bench supply, so the soft start capacitor is not optional on a production board. The output capacitor value is part of the stability condition: the part is optimised for 10 uF ceramic, and a board that substitutes a 47 uF bulk part changes the loop and the transient response.

Two pages worth reading before a purchase order goes out are the power management cross reference and how to verify a drop in replacement; the first lists what else fits the socket, the second is the test sequence for a drop in, and vendor consolidation covers the case where the shortage is already on the line.

Two questions buyers ask

Can the ADP1763 run from a 3.3 V rail? No. The input window stops at 1.98 V, and a 3.3 V source will exceed the absolute maximum. The upstream stage has to be a switching regulator that produces 1.8 V or lower.

Does the fixed 1.2 V version need the adjust pin left open? The fixed versions are set internally and the adjust node is not used, but the exact pin treatment is stated in the data sheet and has to be followed, because leaving a node floating that expects a resistor sets the output to its minimum.