Contact Us

ADM7171ACPZ-R7

Brand: Analog Devices
Analog Devices ADM7171ACPZ-R7 is a analog & mixed-signal component designed for Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

ADM7171ACPZ-R7 — Analog & Mixed-Signal ICs | Superb Automation

ADM7171ACPZ-R7

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The ADM7171ACPZ-R7 from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

ADM7171ACPZ-R7: the reel option of the 1 A low noise LDO, and what changes on a build

The ADM7171ACPZ-R7 is the same 1 A, 2.3 V to 6.5 V CMOS low dropout regulator as the rest of the ADM7171 family, packed on a reel for automated placement. Electrical behaviour does not change with the packing suffix, so the specification that matters stays 5 uV rms of noise from 100 Hz to 100 kHz, 60 dB of rejection at 100 kHz and 42 mV of dropout at 500 mA. What changes is the material handling on the line, and that is where most of the questions on this order code come from.

Published values

ParameterValue
Function1 A CMOS LDO, 2.3 V to 6.5 V input
Output noise, 100 Hz to 100 kHz5 uV rms
PSRR at 100 kHz60 dB
Dropout at 500 mA, VOUT = 3 V42 mV
Quiescent current0.7 mA, no load
Shutdown current0.25 uA at VIN = 5 V
Soft startAdjustable with an external capacitor
Package8-lead LFCSP, 3 mm x 3 mm
Packing suffixR7, reel
Reel quantityPrinted on the box and reel label, confirm against the PO
MSLCheck the moisture sensitivity label on the reel before the bake decision

Packing suffix does not change the die

R7 is a packing code. Before a second reel is released to the line, the label is checked for the full order code, the date code and the lot, and one part from the reel is measured for the two parameters that decide whether the rail behaves: dropout at the working current and the output voltage at no load. A reel of the right family in the wrong voltage option is the most common mix up on a mixed voltage bill of materials, and it does not show up until the rail is out of tolerance on the first article.

Cut tape from a broken reel is a different risk. If a build is short by 200 pieces, cut tape arrives without the original reel label in most cases, so the date code is read from the part marking and the moisture history is unknown. For a 3 mm LFCSP that has been out of the bag for weeks, the safe assumption is a bake before the reflow profile is run.

Why a 1 A LDO ends up on a 300 mA rail

Most boards using this part do not draw 1 A on the rail. The part is chosen for the transient response of 1.5 us on a 1 mA to 500 mA step and for the noise floor, and it is run at a fraction of the rated current so that the load step lands well inside the envelope. That headroom changes the substitute decision: a 500 mA LDO with a tighter noise figure can look better on paper and still fail the step response the board was qualified against.

Verification before a lot is accepted

The check we run on incoming material is short. Output voltage at no load and at the rated current on three parts per lot, dropout at 500 mA, and the shutdown current with the enable pin low. Those four readings separate a genuine reel from a remarked one, and they take a bench supply and a meter rather than a full characterisation bench.

Where a customer needs a second position on this part, the pin to pin cross reference is the starting point, how to verify a drop in replacement sets out the checks a substitution has to pass, and BOM shortage recovery is the short lead time route we quote against.

Two questions buyers ask

Is the R7 reel the same part as the cut tape I already have? Electrically yes, both are the same body and die. The difference is traceability: the reel carries the lot and date code, and cut tape usually does not, which matters when a build has to be traced after a field return.

Can two reels from different lots be mixed in one feeder? Not in a build that has to be traced. Keep one lot per feeder and record the changeover, otherwise a parameter shift between lots cannot be separated from a process shift on the line.