ADM1184ARMZ-REEL7
Product Specifications
ADM1184ARMZ-REEL7
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The ADM1184ARMZ-REEL7 from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
ADM1184ARMZ-REEL7: 0.8 Percent Comparator Accuracy Plus a 1 Percent Divider Is Not 0.8 Percent
The ADM1184 monitors four supply rails with four comparators against an internal 0.6 V reference accurate to 0.8 percent, and provides three open drain enable outputs plus a common power good output, in a 10-lead MSOP powered from 2.7 V to 5.5 V. The accuracy figure applies to the reference and the comparator. The divider that sets each rail threshold is external, so the accuracy of the monitored point is the comparator term plus the divider term plus the tolerance of the rail itself. That sum is what a sequencing specification actually has to survive, and it is usually two or three times the headline figure.
Working out the real threshold window
Monitoring 3.3 V with a divider that puts 0.6 V on the comparator pin means the divider ratio is 5.5 to 1. The 0.8 percent comparator window is plus or minus 26.4 mV at the rail. Resistors at 1 percent each with the same ratio contribute roughly 0.7 percent of the threshold, which is another 23 mV, and a 0.1 percent pair reduces that to 3.3 mV. So the same circuit trips anywhere from 3.25 V to 3.35 V with ordinary resistors and much tighter with a matched network, and a 3.3 V rail at minus 5 percent is 3.135 V: below both windows, which is correct, but with only 100 mV of margin to the worst case.
| Element | Effect on a 3.3 V threshold | How it is controlled |
|---|---|---|
| 0.6 V reference and comparator | Plus or minus 26.4 mV | Fixed by the part |
| 1 percent resistors | About 23 mV | Matched network or 0.1 percent parts |
| Rail tolerance at minus 5 percent | 165 mV below nominal | The margin the monitor has to sit inside |
| Propagation delay | 30 us typical | Blank time against a fast transient |
One rail cannot be sequenced
The three enable outputs follow the first three inputs: OUT1 tracks VIN1, OUT2 tracks VIN2 and OUT3 tracks VIN3. VIN4 is a monitor only, with no associated enable, so a fourth rail can be watched but cannot be brought up by this part. Boards that need four sequenced rails therefore need two devices or an external sequencer, and the mismatch usually turns up when the fourth rail is the one that has to come last. The power good output covers all four inputs and is deasserted as soon as any one of them falls below its threshold.
Assert and deassert are deliberately asymmetric
Power good assertion has an internal 190 ms delay, while deassertion is immediate. That asymmetry is the feature: a rail that dips for a microsecond must remove power good at once, while a rail that comes up cleanly must not release the flag until the supply has been stable for 190 ms. A system that resets a processor from this signal gets a guaranteed settle time after the last rail arrives, at the cost of a 190 ms start up. If that is too long for a specification, the delay cannot be shortened on this part, and the processor has to be reset from a different source.
Open drain outputs and pull ups
All four outputs are open drain, so each needs a pull up to the logic rail it talks to, and the pull up can be to a rail higher than the monitor supply as long as the output ratings allow it. The enables drive the shutdown pins of regulators, which are frequently active low, so the sense of the signal has to be checked against the regulator data sheet rather than assumed. Monitoring a rail that is derived from the same 3.3 V that powers the monitor means the monitor loses its own supply when the rail fails, which is why the usual arrangement powers the monitor from a rail that is always present.
Second sourcing a quad monitor
The substitution question is the reference voltage and the output polarity first, because a 0.6 V reference device cannot drop into a socket set for a 1.24 V reference without changing every divider. The power management cross reference page covers the supervisory class, the pin to pin cross reference page covers the footprint, and lot checks follow the incoming inspection plan.