ADUM7642ARQZ
Product Specifications
ADUM7642ARQZ
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The ADUM7642ARQZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
ADUM7642ARQZ: The A Suffix Caps This Six Channel Isolator at 1 Mbps, Not 25 Mbps
The ADuM7642 is the four forward, two reverse member of the six channel ADuM7640 family in a 20 lead QSOP. Family pages and most distributor listings carry the 25 Mbps headline, but the ordering table splits every one of the four direction options into an A code and a C code, and the split is not a price grade. ADuM7642ARQZ is a 1 Mbps part with a 20 ns maximum propagation delay and a 75 ns maximum pulse width distortion. ADuM7642CRQZ is the 25 Mbps part with 14 ns and 50 ns. A line that copied the ARQZ code because the bus runs at 20 Mbps has bought a part that cannot carry the bus, and the mistake only shows up at first article.
What the 1000 V rms rating does and does not cover
The isolation rating is 1000 V rms for one minute under UL 1577, and the data sheet positions the family against 2.5 kV and 5 kV solutions for cases where functional isolation is enough. Functional isolation is not a shock hazard barrier, so this part does not replace a reinforced barrier on a mains referenced front end. Where the two sides are a control ground and an isolated measurement ground inside the same enclosure, the 1 kV rating is the right class and the QSOP body saves the board area that a wide body isolator would take.
Direction count is fixed by the order code
| Order code | Inputs on side 1 | Inputs on side 2 | Rate and delay |
|---|---|---|---|
| ADuM7640ARQZ | 6 | 0 | 1 Mbps, 20 ns |
| ADuM7641ARQZ | 5 | 1 | 1 Mbps, 20 ns |
| ADuM7642ARQZ | 4 | 2 | 1 Mbps, 20 ns |
| ADuM7643ARQZ | 3 | 3 | 1 Mbps, 20 ns |
| ADuM7642CRQZ | 4 | 2 | 25 Mbps, 14 ns |
The two reverse channels make the 7642 the usual choice for an SPI link, where three or four lines run one way and one or two run back. What the table also shows is that the C code is not the only way to get 25 Mbps: the grade and the direction count are separate fields, so a 25 Mbps link with five forward lines is ADuM7641CRQZ and not a 7642.
Supply current: the per channel figure is not the device total
The front page quotes 1.6 mA per channel maximum from 0 Mbps to 1 Mbps at 3.3 V and 7.8 mA per channel at 25 Mbps. Read against the device tables, the ADuM7642 at 3.3 V and 1 Mbps draws 3.9 mA typical and 4.9 mA maximum on side 1 and 3.4 mA typical and 4.2 mA maximum on side 2, so the whole package is under 10 mA and not the 9.6 mA that six times 1.6 mA would suggest. The dynamic term is 0.19 mA per Mbps per channel, which is what a 1 Mbps SPI clock costs and what a 25 Mbps C grade part would multiply.
Static inputs and the power loss default
The refresh rate is 550 kHz, so a DC input that never toggles is re sent roughly every 1.8 us and the output does not sit undefined. On loss of input side power the output defaults to the high logic state, which matters for an active low enable or an active low reset: the isolated side will see that line go high, so the safe state has to be built with an inverter or a pull down on the far side rather than assumed. Common mode transient immunity is above 15 kV per microsecond, and the C grade keeps the pulse width distortion under 6 ns, which is the number that decides whether a narrow SPI chip select survives the barrier.
Sourcing this code
When the ARQZ code is short, the substitution question is two fields and not one: the C code is a pin compatible rate upgrade and works wherever the timing budget allows, while a different direction count is not a substitution at all. The ADI part second source page covers the grade question, the pin to pin cross reference page covers the footprint, and lot level checks run through the incoming inspection plan.