Contact Us

ADM485JRZ

Brand: Analog Devices
Analog Devices ADM485JRZ is a analog & mixed-signal component designed for Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

ADM485JRZ — Analog & Mixed-Signal ICs | Superb Automation

ADM485JRZ

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The ADM485JRZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

ADM485JRZ: five megabit RS-485 transceiver for a five volt bus

The ADM485JRZ is a half duplex RS-485 transceiver in an 8-lead narrow SOIC, operating from a single 5 V supply at up to 5 Mbps with a common mode range of -7 V to +12 V. It is the low speed member of the family whose 30 Mbps sibling is the ADM1485, and the J suffix on this order code is the commercial temperature grade.

Published values

ParameterValue
Functionhalf duplex RS-485 driver and receiver
Supplysingle 5 V
Data rate5 Mbps
Common mode range-7 V to +12 V
Driver differential output2.0 V minimum, 5.0 V maximum into 50 ohm
Driver propagation delay10 ns typical
Receiver propagation delay15 ns typical
Temperature grade0 C to +70 C
Package8-lead narrow SOIC

The temperature suffix is the first thing to read

J is the commercial grade, 0 C to +70 C. A board that is specified over 0 C to +70 C can use this order code; a board that is specified over -40 C to +85 C cannot, even though the silicon is the same family and the footprint is identical. This is the single most common mistake when a purchasing system replaces a JRZ with an ARZ or the other way round.

The electrical table is written at 5 V plus or minus 5 percent, and the driver output is specified into a 50 ohm load as 2.0 V minimum and 5.0 V maximum. That upper bound is not a typo: it is the limit that keeps the driver inside the RS-485 common mode window when several nodes are transmitting.

5 Mbps against 30 Mbps on the same footprint

At 5 Mbps a bit is 200 ns, and the 10 ns driver delay plus the 15 ns receiver delay is 25 ns, or 12.5 percent of a bit. The same 25 ns against the ADM1485 at 30 Mbps is a 33 ns bit, so the delay alone is 75 percent of the bit period before the cable is counted.

That is why the slower part is the better choice on a long bus: the slew rate is limited, the edges are gentler, and the reflections from a poorly terminated line have time to settle inside the bit. On a short backplane the faster part wins on throughput and loses on emissions.

Common mode range and the ground that moves

The -7 V to +12 V common mode range is the part of RS-485 that survives a plant floor. Two nodes several metres apart can sit volts apart in ground potential and still communicate, because the receiver measures the difference between A and B rather than either against local ground.

The range is a limit, not a guarantee of comfort: at the extremes the receiver threshold shifts and the noise margin shrinks. A bus that regularly runs near +12 V needs the isolated members of this family rather than a larger common mode claim on a non isolated part.

Sourcing and second source

The pin out is the industry 8-lead RS-485 footprint, so several vendors build a compatible part. The checks before accepting one are data rate, common mode range, temperature grade and driver output swing, in that order, and then the fail safe behaviour of the receiver with the bus idle.

The pages below cover the family cross reference, the acceptance test for a substitute, and the routine for a part that has gone short.

For a board that has to keep running while a reel runs out, the pin to pin cross reference is where the family alternatives sit, the ADI second source page is the check list before a substitute goes in, and BOM shortage recovery is how a gap is covered without a new line item.

Two questions buyers ask

Can the ADM485JRZ drive a 120 ohm terminated bus? Yes. The driver is specified into a 50 ohm test load, which is a harder load than two 120 ohm terminations in parallel, so a terminated bus is inside the driver rating.

Does it include a fail safe receiver? This order code is the plain half duplex transceiver. True fail safe behaviour with an idle or shorted bus belongs to other members of the family and has to be checked on the candidate data sheet.