ADM3075EARZ
Product Specifications
ADM3075EARZ
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The ADM3075EARZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
ADM3075EARZ: three volt RS-485 at five hundred kilobit
The ADM3075EARZ is a 3.3 V half duplex RS-485 transceiver in an 8-lead narrow SOIC with 15 kV human body model protection on the bus pins and a -7 V to +12 V common mode range. It sits in the middle of a family that spans 250 kbps to 16 Mbps in the same footprint, at the speed that suits a long slew limited field bus.
Published values
| Parameter | Value |
|---|---|
| Function | half duplex RS-485 driver and receiver |
| Supply | 3.3 V |
| Data rate | 500 kbps |
| ESD on bus pins | 15 kV human body model |
| Common mode range | -7 V to +12 V |
| Temperature range | -40 C to +85 C, +125 C option on the reel part |
| Package | 8-lead narrow SOIC |
One footprint, five data rates
The family splits into three bands: 250 kbps on the ADM3070E, ADM3071E and ADM3072E, 500 kbps on the ADM3073E, ADM3074E and ADM3075E, and 16 Mbps on the ADM3076E, ADM3077E and ADM3078E. The package and the pin out are shared, so the data rate is chosen by order code and the board does not change.
That is convenient for a product family and dangerous for a purchasing substitution. A 16 Mbps part fitted where a 500 kbps part was qualified has faster edges, higher emissions and a shorter bit, which on a long cable is a worse link, not a better one.
Why 500 kbps is the field bus speed
At 500 kbps a bit is 2 us. A 100 m cable at 5 ns per metre is 500 ns one way, so a bit period still contains the cable delay twice over and a reflection has time to decay. The same cable at 16 Mbps gives 62.5 ns per bit, which is shorter than the cable delay itself, and the link depends on termination rather than on the transceiver.
The slew limited edges of the 500 kbps parts also keep the emissions inside the limits of an industrial cabinet without shielding. That is the practical reason most field buses stop at this rate even when the transceiver could go faster.
15 kV on a 3.3 V part
Protection on the bus pins does not depend on the supply voltage, and this part carries the same 15 kV human body model rating as its 5 V relatives. What changes with 3.3 V is the driver output and the receiver threshold, both of which are specified to remain compatible with a 5 V bus.
A mixed bus with 5 V and 3.3 V nodes is normal in RS-485 because the standard defines the differential levels rather than the supply. The node that has to be checked is the receiver threshold, not the driver swing.
Replacement checks
Within the footprint the substitution risk is data rate and temperature option. The reel part carries a +125 C grade that the tube part does not, so a hot cabinet has to be ordered by the reel suffix rather than by the base code.
The pages below hold the family cross reference, the acceptance sequence and the shortage route.
Where a customer needs a second position on this part, the pin to pin cross reference is the starting point, the ADI second source page sets out the checks a substitution has to pass, and how to verify a drop in replacement is the short lead time route we quote against.
Two questions buyers ask
Is the ADM3075EARZ a direct replacement for the ADM3076EARZ? The footprint is the same and the function is the same, but the data rate is 500 kbps against 16 Mbps. Check the cable and the termination before treating one as the other.
Does it work on a 5 V bus? Yes. The receiver thresholds and the driver output are specified for the RS-485 differential levels, so a 3.3 V node can sit on a bus with 5 V nodes.