Contact Us

ADA4522-2ARZ-R7

Brand: Analog Devices
Analog Devices ADA4522-2ARZ-R7 is a analog & mixed-signal component designed for Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

ADA4522-2ARZ-R7 — Analog & Mixed-Signal ICs | Superb Automation

ADA4522-2ARZ-R7

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The ADA4522-2ARZ-R7 from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

ADA4522-2ARZ-R7: two zero drift channels on a 55 volt supply

The ADA4522-2ARZ-R7 is the dual channel ADA4522 in an 8-lead SOIC on reel. Each channel is published at 5 microvolts of maximum offset and 22 nanovolts per degree C of maximum drift, and the package runs from a 4.5 to 55 volt single supply. A dual zero drift part at this voltage is normally bought for one of two reasons: a two stage front end where both stages have to be drift free, or two independent channels that share a rail and a decoupling network.

Published values

ParameterValue
Channels2
Package8-lead SOIC (R-8)
Offset voltage5 uV maximum, per amplifier
Offset voltage drift22 nV/C maximum, per amplifier
Voltage noise, 0.1 Hz to 10 Hz117 nV peak to peak typical
Voltage noise density5.8 nV/root Hz typical at 1 kHz, gain 100
Input bias current50 pA typical
Unity gain crossover3 MHz typical
Gain bandwidth product2.7 MHz typical
Single supply operation4.5 V to 55 V
Absolute maximum supply60 V
Otherintegrated EMI filters, AEC-Q100 qualified
Operating temperature-40 C to +125 C
Packing suffix-R7 marks the reel option

Two channels of drift arithmetic

Per channel the drift is 22 nanovolts per degree C, which is 3.63 microvolts across the published 165 kelvin span, against a 5 microvolt offset. The drift term is therefore about 0.73 of the offset term, which is the property that separates a chopper from a trimmed precision amplifier and the reason a customer will accept a 5 volt rail where a 15 volt part used to sit.

For two channels the worst case sum is 10 microvolts of offset and 7.26 microvolts of drift, both still below what a single non zero drift part contributes at room temperature. At gain 101 the offset appears as 505 microvolts at the output per channel, so the amplifier stops being the limiting error in almost any channel that also has a sense resistor or a divider in it.

The supply range decides the topology

A 4.5 volt minimum means the part cannot be run from a single 3.3 volt rail, and a 55 volt maximum means it can be run from the 48 volt rail it is measuring. Those two facts together rule out the usual trick of powering the front end from a low voltage rail and level shifting afterwards: here the front end can sit on the high rail, which removes a stage, a rail and a failure mode.

Dual supply operation is published as plus minus 2.25 to plus minus 27.5 volts. On a plus minus 24 volt rail the part has 3.5 volts of headroom to its maximum, which is comfortable, and on a plus minus 15 volt rail it has 12.5 volts. Where a customer's rail is unregulated the 60 volt absolute maximum is the number to check against, not the 55 volt operating figure.

What changes when the same function is bought as a quad

The quad member of this family publishes 25 nanovolts per degree C rather than 22, which is 4.125 microvolts across the 165 kelvin span instead of 3.63. A substitution from the dual to the quad is therefore a small specification change, not a formality, and it has to be recorded before a customer signs off a build that was qualified on the dual.

The MSOP code of the same dual is a third option, and it changes the package and the thermal path without changing the electrical table. Which of the three is on the shelf is a scheduling question; which of the three the drawing calls for is a specification question, and the two are easy to confuse when a line is held up.

Buyers usually arrive at the ADI second source page to find the family alternatives, then use BOM shortage recovery to confirm a substitute before it is fitted; the pin to pin cross reference is the routine for a part that has already stopped shipping.

Two questions buyers ask

Is the quad version of this part an exact substitute for the dual? No. The quad publishes 25 nanovolts per degree C of drift against 22 on the dual, which is 4.125 against 3.63 microvolts across the 165 kelvin span. It is a small change but it is a change.

Can both channels run from a 48 volt rail directly? Yes, up to the 55 volt operating maximum and the 60 volt absolute maximum. Each channel input includes the negative rail, so a high side sense resistor can be read without a divider.