AD9238BCPZ-20
Product Specifications
AD9238BCPZ-20
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The AD9238BCPZ-20 from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
AD9238BCPZ-20: two 12-bit channels on three volts, and what the pin compatible 14-bit part would cost
The AD9238 is a dual 12-bit analog to digital converter running from a single 3 V supply, 2.7 V to 3.6 V, in 20, 40 and 65 MSPS speed grades, in a 64-lead LQFP. The suffix on this order code is the speed grade: 20 means 20 MSPS. Each channel has its own sample and hold and its own clock input, so the two can be clocked independently, and the input accepts a differential range from 1 V p-p to 2 V p-p with a 500 MHz bandwidth. The vendor states pin compatibility with the AD9248, the 14-bit part in the same body, which is a procurement fact as much as an engineering one: the same board can carry 12 or 14 bits depending on what is available.
What the vendor page states
| Parameter | Value |
|---|---|
| Resolution and channels | 12 bits, two channels |
| Speed grades | 20, 40 and 65 MSPS |
| Supply | single 3 V, 2.7 V to 3.6 V |
| SNR | 70 dB to Nyquist at the 65 MSPS grade |
| SFDR | 80.5 dBc to Nyquist at the 65 MSPS grade |
| Power | 180 mW at 20 MSPS, 330 mW at 40 MSPS, 600 mW at 65 MSPS for both channels |
| Analog input | 1 V p-p to 2 V p-p differential, 500 MHz bandwidth |
| Channel isolation | better than 85 dB at 10 MHz input |
| On chip | voltage reference, clock duty cycle stabiliser, data output multiplex |
| Package and range | 64-lead LQFP, minus 40 to plus 85 C |
Seventy decibels is 11.3 effective bits, and the LSB changes with the input range
Seventy decibels of signal to noise ratio against a full scale sine puts the effective number of bits at 11.34, and read as noise on a 2 V p-p range it is 223.6 microvolts rms against an LSB of 488.3 microvolts, or 0.458 LSB. Drop the input range to 1 V p-p and the LSB halves to 244.1 microvolts while the noise stays the same in absolute terms, so the same 223.6 microvolts is now 0.92 LSB. The 70 dB figure is referenced to full scale, which is why a smaller input range does not improve the signal to noise ratio even though it looks like it should: it halves the signal with the step size.
Ninety milliwatts per channel at 20 MSPS, 4.6 mW per MSPS at the top grade
Both channels at 20 MSPS draw 180 mW, 90 mW each, while the 65 MSPS grade draws 600 mW for the pair, which is 300 mW per channel and 4.6 mW for every megasample of rate. That 4.6 mW per MSPS is the marginal cost of speed in this family and it is what a system pays for headroom it may not use: a 20 MSPS product that is later pushed to 40 MSPS moves from 180 mW to 330 mW on the same die. On a 3 V rail the current goes from 60 mA to 110 mA, which matters on a battery instrument long before it matters on a line powered one.
Two independent clocks and 85 dB between the channels
Independent clock inputs per channel mean the two halves can run at different rates, which is useful when one channel watches a fast transient and the other a slow temperature signal, but the 85 dB channel isolation figure is measured at 10 MHz and it is the number that decides whether a large signal on one channel corrupts a small one on the other. In an ultrasound receive path this is the specification that sets how much front end gain can be put in front of each channel before leakage through the die becomes visible. The clock duty cycle stabiliser is the second half of the same argument: at 20 MSPS with a 50 MHz clock, a duty cycle error of a few percent shifts the sampling instant on alternate cycles and shows up as even order distortion.
Before the order goes out
The AD9238 and the AD9248 share a footprint and differ in resolution, and inside the AD9238 the three speed grades differ only in the suffix, so a bill of materials that lists the family without the suffix has not specified a part. The ADC and DAC cross reference lists the converters that share this body and the resolution each carries, the obsolete part hub is where the life cycle status of the 20 and 40 MSPS grades is tracked, and the analog and mixed signal category page holds the rest of the converter family.
AD9238BCPZ-20: the clock, not the converter, sets the last ten decibels
Seventy decibels of signal to noise ratio is the number on the row, and jitter on the clock is what usually takes it away. The limit is arithmetic: the signal to noise ratio that clock jitter allows is one over two pi times the input frequency times the jitter, in decibels. At 10 MHz, which is Nyquist for the 20 MSPS grade in this code, 70 dB allows about 5 ps of jitter. At 100 MHz the same 70 dB allows 0.5 ps, which is an order of magnitude tighter and usually the point where a cheap oscillator stops being adequate.
| Item | Value for this code | Where it bites |
|---|---|---|
| Resolution | 12 bits, two channels | 70 dB of signal to noise is 11.34 effective bits |
| Speed | 20 MSPS, 10 MHz Nyquist | 5 ps of clock jitter keeps 70 dB at the top of the band |
| Input range | 1 V peak to peak to 2 V peak to peak | 223.6 uV of noise is 0.92 LSB at 1 V and 0.46 LSB at 2 V |
| Analog bandwidth | 500 MHz | A 10 MHz signal on a 20 MSPS clock is already at Nyquist |
| Power | 180 mW at 20 MSPS for both channels | 90 mW per channel, 9 mW per megasample |
| Pin compatibility | Same body as the 14 bit AD9248 | One board can carry either resolution, which is a supply decision |
Jitter is the only term that scales with input frequency
Quantisation noise is fixed by the resolution and the input range, and thermal noise is fixed by the amplifier in front, but the noise that jitter contributes rises with the input frequency and is zero at dc. That is why a converter that meets its figures at 1 MHz can miss them by 20 dB at 100 MHz without anything being wrong with the part. The practical rule is to take the highest input frequency the application will see, not the sampling rate, and to size the clock source from that number.
Two clocks, and the isolation between them
Each channel has its own sample and hold and its own clock input, so the two can be sampled at different instants, and the isolation between channels is better than 85 dB at a 10 MHz input. For a quadrature receiver that means the two channels can share one clock with a defined phase, and for two independent sensors it means the sampling instant of one does not disturb the other. The 85 dB figure is a channel to channel number at 10 MHz, and it falls as the input frequency rises, in the same way the jitter term does.
What the twelve bit and fourteen bit bodies share
The vendor states pin compatibility with the 14 bit part in the same body, so a board can be specified once and populated at either resolution depending on what is available. That is a supply decision with an engineering consequence: the 14 bit part has the same input range and roughly the same power, so the change shows up in the noise floor rather than in the pinout. The range this converter sits in is listed on the analog and mixed signal line card, the cross reference for a pin compatible alternative is under pin to pin cross reference, and reel quantities and lead times are confirmed on the lead time page.
Request Quote — In Stock, 100% New & Original, Full Warranty