AD7949BCPZ
Product Specifications
AD7949BCPZ
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The AD7949BCPZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
AD7949BCPZ: 14 Bits and Eight Channels on 4 mm by 4 mm
The AD7949BCPZ is a 14 bit, eight channel PulSAR converter at 250 kSPS in a 20-lead LFCSP measuring 4 mm by 4 mm. It puts the multiplexer, the reference and the sequencer on the die: the internal reference is selectable at 2.5 V or 4.096 V, there is a temperature sensor, a selectable one pole filter and a channel sequencer, and the inputs can be configured as unipolar single ended with ground sense, differential or pseudobipolar. Typical integral nonlinearity is plus or minus 0.5 LSB and differential is plus or minus 0.25 LSB, signal to noise and distortion is 85 dB at a 20 kHz input and total harmonic distortion is minus 100 dB there. Power is 2.9 mW at 2.5 V and 200 kSPS, 10.8 mW at 5 V and 250 kSPS, and standby current is 50 nA.
Published values
| Parameter | Value |
|---|---|
| Resolution | 14 bit, no missing codes |
| Throughput | 250 kSPS |
| Inputs | Eight channels, unipolar, differential or pseudobipolar |
| INL and DNL | Plus or minus 0.5 LSB and 0.25 LSB typical |
| SINAD and THD | 85 dB and minus 100 dB at 20 kHz |
| Reference | Internal 2.5 V or 4.096 V, external up to VDD |
| Supply | 2.3 V to 5.5 V, logic interface 1.8 V to 5.5 V |
| Power | 2.9 mW at 2.5 V and 200 kSPS, 10.8 mW at 5 V and 250 kSPS |
| Standby current | 50 nA |
| Conversion time | 2.2 us from the convert edge |
| Temperature range | Minus 40 to plus 85 degrees Celsius |
| Body | 20-lead LFCSP, 4 mm by 4 mm |
85 dB is 13.8 bits, and the reference decides the rest
Signal to noise and distortion of 85 dB is 13.8 effective bits, so a 14 bit result from this part is close to honest at low frequency. What is not honest is assuming that the internal reference holds that accuracy over temperature, because a reference with a few ppm per degree moves the full scale, and the converter's linearity says nothing about it. A 14 bit code on the 4.096 V internal reference is 250 uV, and a total unadjusted error of a few millivolts is already several codes. For absolute measurements, feed an external reference into the REF pin, which the part accepts from 0.5 V up to the supply, and keep the internal one for ratiometric work where its drift cancels.
Three input configurations on one set of pins
The same eight pins can be wired as eight single ended inputs with ground sense, as four differential pairs, or as pseudobipolar inputs that swing around mid-scale. Unipolar mode reads 0 V to the reference, differential mode reads the difference between an input and its common pin with the common range restricted near the rails, and pseudobipolar reads plus or minus half the reference plus an offset, which is how a bipolar sensor is handled without a level shifter. Getting this wrong is a common mistake on a first build: the configuration register setting and the wiring have to match, and a pseudobipolar setting on single ended wiring gives a reading that looks like a broken channel.
The 2.2 us conversion and the driver it implies
At 250 kSPS the cycle is 4 us, of which 2.2 us is conversion, leaving about 1.8 us to acquire the next channel. That window is short for a multiplexed input with a large source resistance, and the datasheet pairs the part with the ADA4841-1 driver for exactly this reason. A circuit that drives the converter from a resistive divider without a buffer will show code dependent errors that look like linearity problems but are acquisition settling. The one pole filter in the part helps with broadband noise and does not help with settling, so it is not a substitute for the driver.
Standby current and the always on monitor
Fifty nanoamps of standby current means the part can sit in a battery instrument and be woken for a burst of conversions, and 2.9 mW at 200 kSPS on 2.5 V is 1.16 mA while running. A monitor that takes sixteen channels once a second spends almost all of its time in standby, so the average current is set by the standby figure and the wake up time, not by the 250 kSPS headline. The temperature sensor on the die is useful for cold junction and board level compensation, and it is a die temperature reading rather than an ambient one, so it must be calibrated against the thermal path if it is used for anything other than drift tracking. The ADI part second source page lists the grades that are equivalent, the amplifier cross reference page groups the converter drivers that settle inside this window, and the lead time page shows what is available now.