Contact Us

AD7663ASTZ

Brand: Analog Devices
Analog Devices AD7663ASTZ is a analog & mixed-signal component designed for Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

AD7663ASTZ — Analog & Mixed-Signal ICs | Superb Automation

AD7663ASTZ

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The AD7663ASTZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

AD7663ASTZ: A 16-Bit 250 kSPS Converter with Six Input Ranges and No Pipeline Delay

The AD7663 is a charge redistribution successive approximation converter with 16 bits, 250 kSPS of throughput, a single 5 V supply and a resistor input scaler that gives six selectable ranges from one part: plus or minus 10 V, plus or minus 5 V and plus or minus 2.5 V, and 0 V to 10 V, 0 V to 5 V and 0 V to 2.5 V. It is a hardware factory calibrated part, so the offset and gain coefficients are trimmed at production rather than loaded by the host, and it comes in a 48-lead LQFP or a 48-lead LFCSP specified from minus 40 C to plus 85 C.

No pipeline delay means the first sample is the answer

A pipelined converter returns a result several conversion periods after the sample it belongs to, which is acceptable in a continuous stream and awkward in a multiplexed system where the channel changes between samples. The AD7663 has no pipeline delay: the data word that comes out belongs to the conversion that was just started, so a channel switched on one conversion and read on the next gives that channel and not a neighbour. In a six channel system stepping through a multiplexer, that removes the skew correction that a pipelined part forces into the control firmware, and it makes single shot measurements on a multiplexed front end straightforward.

The linearity figure in codes and in volts

The integral nonlinearity is 3 LSB maximum, which the vendor also states as 0.0046 percent of full scale, and there are 16 bits with no missing codes, so every one of the 65536 codes appears. On the plus or minus 10 V range the span is 20 V, one LSB is 305 uV, and 3 LSB is 916 uV, which is the 0.0046 percent figure. On the plus or minus 2.5 V range the span is 5 V, one LSB is 76 uV, and 3 LSB is 229 uV. The same converter therefore looks four times better in volts on the narrow range and identical in codes, which is the usual reason to select the smallest input range that still fits the signal.

Speed, power and the crossover point

Dynamic performance is 90 dB typical signal to noise plus distortion at 100 kHz and minus 100 dB typical total harmonic distortion, both measured on the part as shipped. Power dissipation is 35 mW typical at the full 250 kSPS throughput, 15 uW at a 100 SPS throughput and 7 uW maximum in power-down. Those three numbers describe three different operating modes rather than a linear scaling: 35 mW at 250 kSPS is 140 uJ per conversion, and 15 uW at 100 SPS is 150 uJ per conversion, so at the low end the fixed supply current dominates and the conversion itself is nearly free. A system that samples in bursts should use power-down between bursts rather than run continuously at a low rate, because the second choice keeps the whole analogue block awake.

ParameterValueWhat it decides
Resolution16 bits, no missing codes65536 codes, 305 uV each on a 20 V span
Throughput250 kSPS4 microseconds per conversion
Integral nonlinearity3 LSB maximum, 0.0046 percent of full scale916 uV on plus or minus 10 V, 229 uV on plus or minus 2.5 V
Signal to noise plus distortion90 dB typical at 100 kHzAbout 14.6 effective bits at that frequency
Total harmonic distortionMinus 100 dB typical at 100 kHzHarmonics below 1 LSB on a 20 V span
Input rangesSix: three bipolar, three unipolarSmallest range that fits the signal gives the best volts per code
Pipeline delayNoneMultiplexed channels need no skew correction
SupplySingle 5 VNo separate analogue rails
Power35 mW at 250 kSPS, 15 uW at 100 SPS, 7 uW downBurst sampling should use power-down between bursts
InterfacesParallel 8 or 16 bit, serial 3 V or 5 V logicEither a bus or a two wire port from one part
Package48-lead LQFP or LFCSPSame die, different thermal and assembly path

The family socket and the upgrade path

The part is pin compatible with the AD7660, AD7664 and AD7665, which sit at different throughputs and input configurations in the same PulSAR table, so a build can start with one member and move to another without changing the footprint. That matters when a programme's sample rate requirement grows after the board is released, and it matters for procurement when one member is on allocation and another is not. The 3 LSB linearity is the same in all of them, so the move between members is about speed and input type rather than accuracy.

Typical uses are data acquisition, motor control, instrumentation, spectrum analysis and medical instruments, where a 5 V single supply, 16 bits and no pipeline delay are the deciding combination. For a mixed converter BOM, the ADC and DAC cross reference page lists the pin compatible pairs, the obsolete part cross reference hub covers what to do when a member of the family is discontinued, and the how to verify a drop in replacement page sets out the checks before a substitution is approved.