Contact Us

AD7302BRUZ

Brand: Analog Devices
Analog Devices AD7302BRUZ is a analog & mixed-signal component designed for Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

AD7302BRUZ — Analog & Mixed-Signal ICs | Superb Automation

AD7302BRUZ

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The AD7302BRUZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

AD7302BRUZ: Two 8-Bit Channels, a Parallel Bus and 1.2 us of Settling

The AD7302 is a dual 8-bit voltage output converter in a 20-lead package that runs from a single supply of 2.7 V to 5.5 V and takes its data from a parallel microprocessor bus. The output buffers swing rail to rail with a typical settling time of 1.2 us, the reference is either derived from the supply or applied externally at a pin, both channels can be updated together from the LDAC input and cleared from the CLR input, and power down takes the part below 1 uA at 25 degrees C. Supply current is 3 mA maximum at 3.3 V, which is 15 mW at 5 V typical, and the parts are offered in DIP, SOIC and TSSOP.

19.5 mV per code on 5 V, 12.9 mV on 3.3 V

Eight bits on a 5 V span is 256 codes of 19.5 mV, and on a 3.3 V span it is 12.9 mV. Those steps are coarse enough that the part is chosen for what it does not need: a coarse gain trim, a threshold, a bias point, a contrast or volume setting. Anything that needs a smooth waveform or a fine set point is in the wrong family, and the 1.2 us settling time is what would otherwise suggest a waveform application. The pair of channels in one package with a simultaneous LDAC update is the reason the part survives: two related levels that must change together, such as a differential offset pair, are exactly what an 8-bit dual converter is for.

The reference from the supply is not a reference

With the internal mode selected the converter uses the supply as its reference, so the output is a fraction of VDD and the reading is ratiometric to the rail. On a 5 V rail with 5 percent tolerance the full scale is 4.75 V to 5.25 V, which is a 10 percent spread, ten times worse than the 8-bit resolution. That is fine when the load is also ratiometric, which is the case for an LCD contrast voltage or a bridge excited from the same rail, and it is wrong for an absolute set point, where an external reference at the REFIN pin is the only way to get the 8 bits to mean anything.

ParameterValueWhat it decides
Resolution8 bits, two channels19.5 mV per code on 5 V, 12.9 mV on 3.3 V
Supply2.7 V to 5.5 V singleRuns from a 3.3 V or a 5 V logic rail
InterfaceParallel, 8-bit busDirect connection to a host data bus
ReferenceSupply derived or external at a pinRatiometric or absolute, by the REFIN connection
Output swingRail to railUses the full supply span for the output
Settling time1.2 us typicalFast enough for a coarse waveform, not for audio
Supply current3 mA maximum at 3.3 V10 mW at 3.3 V, 15 mW typical at 5 V
Power downBelow 1 uA at 25 degrees CThe off state of a battery instrument
UpdateLDAC, both channels togetherTwo levels change on the same edge
ClearAsynchronous CLRReturns both outputs to zero without the bus
Channel selectA/B pinOne data bus writes either channel
Package20-lead DIP, SOIC or TSSOPThrough hole for legacy boards, TSSOP for new ones
Logic levelsCMOS and TTL compatibleInterfaces to 5 V and 3.3 V hosts

Double buffered registers and the LDAC pin

Data is loaded into an input register and then transferred to the converter register, either immediately or on a LDAC edge. That two step arrangement is what allows a host to prepare two codes and change both outputs at one instant, so the pair steps together rather than 1.2 us apart. On a differential offset pair that difference is invisible, and on a two channel level control it is audible or visible as a jump. The input registers also mean the host can write channel A, do other work, and then write channel B, without the first channel changing before the second is ready.

What the parallel bus buys in 2026

A parallel interface costs eight data lines and two or three control lines, which is a lot for a modern board where the host has a SPI port and no spare parallel bus. The part remains in production because it drops into boards where a field programmable gate array or an older microcontroller drives a parallel bus, and because a parallel write is a single bus cycle with no framing overhead. For a new board the SPI equivalents of the same function are the better choice, and the decision is a firmware and pin count decision rather than an electrical one.

Sourcing a legacy dual converter

The parallel interface and the 20-lead footprint are the constraints that keep this part in a bill of materials, so a substitute has to match both before the electrical comparison starts. Parts that can be compared on resolution, interface and reference arrangement are listed in ADC DAC cross reference, the check list for a same footprint replacement is in how to verify a drop in replacement, and the route when the original code is discontinued is covered in obsolete part cross reference hub.