AD667KNZ
Product Specifications
AD667KNZ
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The AD667KNZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
AD667KNZ: 12 Bits, Guaranteed Monotonic, With a 10 V Reference On Board
The AD667KNZ is a 12 bit voltage output digital to analog converter in the 28-lead DIP body, and the K grade is the tighter of the two published columns. It carries a 10.00 V reference on the die, quoted between 9.90 V and 10.10 V, so the converter does not need an external reference to hold its full scale, and its transfer characteristics are guaranteed monotonic over the temperature range, which is the property that matters in a control loop. Unipolar output ranges of 0 V to +5 V and 0 V to +10 V are set by pin strapping, and a bipolar offset pin provides the symmetric ranges without extra components. The output stage sources and sinks current, with a short circuit current in the region of 40 mA, so it can drive a remote load without a buffer in light duty work.
Published values
| Parameter | Value |
|---|---|
| Resolution | 12 bits |
| Monotonicity | Guaranteed over the temperature range, both grades |
| Reference output | 10.00 V nominal, 9.90 V to 10.10 V |
| Unipolar ranges | 0 V to +5 V, 0 V to +10 V by pin strapping |
| Bipolar ranges | Set at the bipolar offset pin |
| Digital inputs | 5 V logic thresholds, 12 data lines plus control |
| Feedback resistor | 10 k, brought out for range scaling |
| Output drive | Short circuit current in the region of 40 mA |
| Body | 28-lead DIP, N suffix |
| Grades | J and K columns, K with the tighter linearity |
Monotonic is the specification a control loop actually needs
A converter that is accurate but not monotonic can output a lower code for a higher input at one transition, and in a closed loop that shows up as a limit cycle: the controller keeps stepping and the output never settles. Guaranteed monotonicity means every code transition moves the output in the same direction, so a servo loop can settle to one bit. For a 12 bit part driving a valve positioner or a setpoint input, that property is worth more than a linearity figure in the last digit, and it is the first question to ask when a cheaper converter is proposed as a substitute.
The on board reference and its 1 percent window
The reference is quoted at 10.00 V with a plus or minus 1 percent window, so full scale is accurate to about 1 percent before any trim. Most systems calibrate at the top of the range anyway, either in firmware or with the gain trim pin, so the window costs nothing at the system level. What the on board reference does buy is drift tracking: the reference and the converter share a die and a temperature, so their drifts largely cancel, and a system that would otherwise need a precision external reference can use the internal one and spend the difference on the amplifier chain.
Sockets, grades and the DIP question
The 28-lead DIP body is a through hole part in a surface mount world, and that is the main sourcing issue around this converter: it stays in production for legacy instruments and for industrial boards that are still hand assembled or socketed. The K grade is selected on linearity, so a J grade part in the same socket will convert, but the program's accuracy budget has to absorb the difference. Where the exact grade is not available, the practical options are a J grade with a calibration step or a module that carries the same function on a smaller board. The ADC and DAC cross reference lists the converter families we supply, the ADI second source page covers grade equivalence, and the obsolete part cross reference hub covers end of life codes.