Contact Us

TJA1042T/1

Brand: NXP Semiconductors
NXP Semiconductors TJA1042T/1 is a mcu & embedded component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TJA1042T/1 — MCU & Embedded Processors | Superb Automation

TJA1042T/1

NXP Semiconductors — MCU & Embedded Processors

Product Overview

The TJA1042T/1 from NXP Semiconductors is a microcontroller / embedded processor engineered for real-time control, signal processing, and connectivity. NXP Semiconductors provides secure connectivity solutions, embedded processors, and automotive-grade MCUs for edge computing.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • ARM Cortex / RISC-V / proprietary core with high-performance real-time processing
  • Integrated flash memory and SRAM for efficient code execution
  • Rich peripheral set: UART, SPI, I2C, ADC, timers, PWM
  • Low-power modes for battery-operated and energy-sensitive applications
  • Hardware security features: secure boot, crypto accelerator, TRNG
  • Extensive development ecosystem with IDE, HAL, and RTOS support

Key Specifications

Core—
Max FrequencyMHz
FlashKB
SRAMKB
GPIO—
ADCbits
Interfaces—
Supply VoltageV
Operating Temp°C
Package—

Applications

Industrial Motor Control IoT Edge Nodes Consumer Electronics Automotive Body Control Smart Home & Appliances Medical Portable Devices

Request Quote — In Stock, 100% New & Original, Full Warranty

TJA1042T/1: SO8 CAN FD transceiver with standby and a SPLIT output

TJA1042T/1 is the SO8 member of the standby line with a SPLIT output on pin 5 in the TJA1042 high speed CAN transceiver line with standby mode, described by Rev 7 family document. It is the same standby transceiver as the /3 code with a SPLIT output instead of a VIO supply. The part keeps the bus at a defined recessive level through a split termination, which is the quieter arrangement, and gives up the direct 3.3 V interface in exchange.

Order code and package

Order codeTJA1042T/1
Variant function on pin 5SPLIT output on pin 5; standby is selected by the STB input
PackageSO8, 3.9 mm body width, 8 pins
ProtocolISO 11898-2:2016, SAE J2284-1 to SAE J2284-5 and SAE J1939-14
Maximum data rate5 Mbit/s in the CAN FD fast phase, with shorter propagation delay on the B and C variants
Supply voltage on VCC4.5 to 5.5 V
Logic supply on VIO2.8 to 5.5 V on the /3 variants
Temperature rangeminus 40 to plus 150 C virtual junction
QualificationAEC-Q100
DatasheetRev 7 family document

Electrical parameters that decide the application

Bus fault voltageminus 58 to plus 58 V on CANH and CANL
Supply currentStandby 10 to 15 microamps on VCC and 5 to 14 microamps on VIO, normal recessive 2.5 to 10 mA and dominant 20 to 70 mA
Electrostatic dischargeplus or minus 8 kV IEC 61000-4-2 at CANH and CANL
Thermal resistance92 K/W junction to ambient in the SO8 body
Wake and diagnostic pinsSTB input selects standby with bus wake-up, pin 5 is SPLIT on the plain codes and VIO on the /3 codes
Bus pinsCANH and CANL, differential, with the recessive level set by the on chip driver or by a SPLIT output where the code carries one
Logic levelsdigital pins referenced to VCC, so a 3.3 V controller needs 5 V tolerant inputs
Behaviour with the supply offthe transceiver disengages from the bus so an unpowered node does not load the network
ProtectionTXD dominant time-out, undervoltage detection and thermal shutdown are named in every document in this family
Ordering stringthe suffix after the slash carries the body, the packing and the variant, so it has to be quoted in full on a purchase order

Points to check before this part goes on a BOM

SPLIT holds the midpoint of a split termination at half of VCC, so two 60 ohm resistors with a capacitor to ground become a 120 ohm differential load with the common mode pinned. That is the arrangement that keeps a long, unbalanced harness from radiating, and the pin has to be connected for it to exist at all.

The digital side runs from VCC, so a 3.3 V controller needs 5 V tolerant inputs and reads a 5 V RXD. Where that is not available the /3 code is the same silicon with a supply pin on pin 5, and the bus figures do not change between them.

Standby current is 10 to 15 microamps, the same as the /3 code, and because there is no VIO pin the whole sleep budget sits on one rail: 15 microamps is 131.4 mAh across a year.

The part carries the base propagation delay of the line rather than the shorter delay of the B and C variants, so the timing window is the wider one. At 5 Mbit/s the high to high path alone is specified across a 210 ns window, and a network with long stubs eats into that.

Bus pins stand minus 58 to plus 58 V and carry plus or minus 8 kV IEC 61000-4-2, so a short to a 24 V rail with the supply off is inside the rating and a short to a 48 V rail is not.

The SO8 body is 92 K/W, which is 10 K better than the older generation parts and 63 K worse than the HVSON8 body of the same die. The 350 mW of a dominant bus is a 32 C rise here, so the package is not the limit until the ambient passes 110 C.

Where this order code fits

It suits 5 V controllers and boards where the split termination is already drawn, and it is the common comparison against the /3 code when a supply pin is not available. Boards weighing one CAN transceiver against another start from our CAN Bus Transceiver Selection page, and boards replacing a part that has gone end of life start from the Component Lead Time Solutions page.

Questions buyers ask

What is the SPLIT pin for? It holds the midpoint of a split termination at half the supply so the bus common mode is defined, which lowers emission. It is an output and must not be tied to a rail.

Can it drive a 3.3 V controller directly? Not cleanly. The digital pins sit at VCC and the controller needs 5 V tolerant inputs. The /3 code puts a VIO supply on pin 5 for a direct 3.3 V interface.

Does it support CAN FD at 5 Mbit/s? Yes, ISO 11898-2:2016 with 5 Mbit/s timing in the fast phase, with the wider delay window of the base variant.

SUPERB holds and sources NXP interface lines including this order code for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated. When a line is changing, the One Stop BOM Sourcing page sets out the checks that keep a substitute from failing on the bench.