Contact Us

ADA4805-2ARMZ-R7

Brand: Analog Devices
Analog Devices ADA4805-2ARMZ-R7 is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

ADA4805-2ARMZ-R7 — Analog & Mixed-Signal ICs | Superb Automation

ADA4805-2ARMZ-R7

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The ADA4805-2ARMZ-R7 from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

ADA4805-2ARMZ-R7: 105 MHz on Half a Milliamp per Amplifier

The ADA4805-2ARMZ-R7 is a dual voltage feedback amplifier with 105 MHz of bandwidth, 160 volts per microsecond of slew rate and 500 microamps of supply current per amplifier. It is the part used to drive a high resolution converter when the amplifier cannot be allowed to dominate the power budget. Buyers reach this page from portable instruments, active filters and ADC driver stages that were previously running at ten times the current.

What the part contains

Two rail to rail output amplifiers with a 125 microvolt maximum offset, 0.2 microvolts per degree Celsius of typical drift and 1.5 microvolts per degree maximum, settling to 0.1 percent in 35 ns, and a shutdown pin that drops the supply current to 2.9 microamps with a 3 microsecond turn on. Voltage noise is 5.9 nanovolts per root hertz and current noise is 0.6 picoamps per root hertz. Supplies can be plus and minus 1.5 V to plus and minus 5 V, or single 3 V and 5 V, and the part is specified at all three. The body is an 8-lead MSOP over -40 C to +125 C, and a defence grade version exists against the AQEC standard.

Key parameters

ParameterValue
Channels2
Bandwidth at gain 1105 MHz
Slew rate160 V per microsecond
Settling to 0.1 percent35 ns
Supply current per amplifier500 microamps
Offset voltage125 microvolts maximum
Offset drift0.2 microvolts per degree typical
Voltage noise5.9 nanovolts per root hertz
Shutdown current2.9 microamps
Turn on from shutdown3 microseconds
Package8-lead MSOP
Temperature range-40 C to +125 C

What the numbers mean on a board

A 105 MHz gain bandwidth product is 10.5 MHz at a gain of 10 and 1.05 MHz at a gain of 100, so the headline bandwidth belongs to a buffer. In a converter driver running at a gain of 2, the closed loop bandwidth is about 52 MHz, and the 160 V per microsecond slew rate into a 2 V peak to peak signal supports 25.5 MHz of full power bandwidth. Slew rate, not the small signal figure, sets the limit for a large signal, and 25.5 MHz is still far above what a 1 MSPS converter needs.

Five hundred microamps at 5 V is 2.5 mW per amplifier, so a dual is 5 mW. Against a 20 bit converter that draws 15 mW, the amplifier no longer doubles the power budget, which is the whole point of the part. The 125 microvolt offset is 2 codes of a 16 bit converter at a 4.096 V reference, so it is negligible in a 16 bit system and about 13 codes in a 20 bit one, where a calibration or a chopper amplifier is required.

Offset drift of 0.2 microvolts per degree over 100 degrees is 20 microvolts, which stays below the initial offset over the whole industrial range. Noise of 5.9 nanovolts per root hertz across a 100 kHz band is 1.87 microvolts rms, so in a wideband measurement the resistor noise around the amplifier usually dominates rather than the amplifier itself. The 3 microsecond turn on from shutdown is what allows the part to be switched on between converter samples rather than left running.

Where it is used

  • Drivers for high resolution successive approximation converters
  • Battery powered instrumentation and portable analysers
  • Micropower active filters
  • Photodiode and photomultiplier front ends
  • Reference buffers in data acquisition

Driving a converter input and using the shutdown pin

A 105 MHz amplifier with a 125 microvolt offset is a good match for a 16 bit converter at 1 MSPS, where the sample capacitor is a few tens of picofarads and the acquisition window is hundreds of nanoseconds. The settling figure to use is the 35 ns to 0.1 percent, not the bandwidth: a converter samples the settling tail, and an amplifier that is fast but rings leaves a code error that changes with the previous sample. Add a small series resistor between the amplifier and the converter input to isolate the capacitive load.

The shutdown pin is the part that makes this amplifier interesting in a duty cycled instrument. At 2.9 microamps and a 3 microsecond turn on, the amplifier can be switched on for the conversion and off between samples, and the average current falls below the quiescent figure. The catch is that the first sample after turn on has a thermal transient in the input stage, so discard one conversion or wait the settling time the data sheet specifies.

Sourcing notes and next step

The dual comes in an 8-lead MSOP and the single in a 6-lead SOT-23 or SC70, so the two are not interchangeable and the footprint decides which one a board can take. The defence grade version carries a different order code and a controlled baseline, which matters when a programme requires one fabrication site. Standard industrial stock is normally available.

Amplifier choices by bandwidth, noise and supply current are compared on the amplifier cross reference page, and the checks for confirming a substitute in a released socket are on the drop in replacement verification page. The rest of the catalogue is on the analog and mixed signal family page. Send the gain, the load and the quantity and we confirm stock and date code.

Request Quote — In Stock, 100% New & Original, Full Warranty