ADA4807-1ARJZ-R7
Product Specifications
ADA4807-1ARJZ-R7
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The ADA4807-1ARJZ-R7 from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
ADA4807-1ARJZ-R7: 3.1 Nanovolts per Root Hertz on One Milliamp
What this part is
The ADA4807-1 is a single voltage feedback amplifier with a rail to rail input and output, a noise density of 3.1 nanovolts per root hertz and 0.7 picoamps per root hertz of current noise, running on 1 mA of quiescent current. The combination is the point of the part: a 200 MHz amplifier that a battery instrument can afford, in a 6 lead SC70 or a 6 lead SOT-23 body.
It has a 225 volt per microsecond slew rate, settles to 0.1 percent in 47 nanoseconds on a 4 V step, and quotes a maximum offset of 125 microvolts with 3.7 microvolts per degree C of drift. Distortion is minus 141 and minus 144 dBc of second and third harmonic at 1 kHz, minus 112 and minus 115 dBc at 100 kHz, and minus 95 and minus 79 dBc at 1 MHz, which is what makes it usable as a converter driver rather than only as a buffer. A disable pin drops the quiescent current to 2.4 microamps, and the supply range is 2.7 V to 11 V, or plus and minus 1.5 V to plus and minus 5 V.
Published figures that matter to a buyer
| Voltage noise | 3.1 nanovolts per root hertz at 100 kHz |
| Current noise | 0.7 picoamps per root hertz at 100 kHz |
| Bandwidth | 200 MHz at minus 3 dB, small signal |
| Slew rate | 225 volts per microsecond |
| Settling | 47 nanoseconds to 0.1 percent on a 4 V step |
| Offset | plus or minus 20 microvolts typical, 125 microvolts maximum |
| Offset drift | 0.7 microvolts per degree C typical, 3.7 maximum |
| Quiescent current | 1 mA enabled, 2.4 microamps disabled |
| Supply | 2.7 V to 11 V, or plus and minus 1.5 V to plus and minus 5 V |
| Distortion | minus 112 and minus 115 dBc at 100 kHz, 2 V peak to peak into 1 kohm |
| Body | 6 lead SC70 or 6 lead SOT-23 |
Where the headline numbers stop
Three point one nanovolts per root hertz over a 1 MHz band is 3.1 microvolts rms, which is 25 times the typical offset of 20 microvolts and 40 times the maximum drift over temperature. A wideband channel is limited by noise and not by offset, and the place to spend money is the bandwidth, not the grade. Over a 10 kHz band the noise is 0.31 microvolts rms, where the offset starts to matter again.
The slew rate and the bandwidth do not belong to the same signal. At 1 V peak, 225 volts per microsecond is a full power bandwidth of 35.8 MHz, so a large signal sees a tenth of the 200 MHz small signal figure. The 47 nanosecond settling of a 4 V step to 0.1 percent is a 4 mV error, so it is a settling figure for a converter that resolves 4 mV or coarser, which is about 10 bits on a 4 V span; a 16 bit converter needs longer and should be budgeted from the settling curves, not from the headline.
One milliamp at plus and minus 5 V is 10 mW, and the disable pin takes that to 24 microwatts, a factor of 400. On a multiplexed instrument that measures in bursts, the disable pin is worth more than a lower power amplifier with worse noise, because the duty cycle does the averaging.
Applications where it fits
- Driving high speed precision converters up to 18 bits, where settling and distortion both matter.
- Active filters and programmable gain stages in portable instruments.
- Transimpedance and photodiode front ends where the 0.7 picoamp current noise keeps the shot noise visible.
- Battery powered test instruments with a high channel density.
- Buffer and cable driver stages in data acquisition.
Two questions buyers ask
Is the 125 microvolt maximum offset a problem for a 16 bit channel? On a 10 V span it is 12.5 ppm, which is about 0.8 of a 16 bit count. It is not the limit for a converter driver, where the settling and the distortion are the terms that matter, and it can be trimmed in a direct current channel if it needs to be. A part chosen for a 0.1 ppm offset is a different part with a different bandwidth.
Does the part stay stable at a gain below one? It is specified as a voltage feedback amplifier with rail to rail input and output and it is characterised for the usual configurations, but attenuation and capacitive load both change the loop, and the data sheet has the curves for capacitive load isolation. A photodiode front end with a large junction capacitance is the case that needs that curve rather than the headline bandwidth.
Sourcing notes and next step
ADA4807-1ARJZ-R7 is the single amplifier in the 6 lead SOT-23 body on tape and reel; the ARJZ and the SC70 code are two different footprints in the same family and the dual and quad members are separate order codes. The amplifier cross reference page sets out the fields for an operational amplifier substitution, the medical device components page covers traceability for instrument builds, and the analog and mixed signal IC family page lists the rest of the amplifier line.
Request Quote — In Stock, 100% New & Original, Full Warranty